National Instruments 781069-01 Operating Instructions And Specifications Download Page 19 | Manualshive

Page: 19 / 25

National Instruments 781069-01 Operating Instructions And Specifications Download Page 19

©

National Instruments Corp.

19

NI 9207E Operating Instructions and Specifications

Safety

Safety Voltages

Connect only voltages that are within the following limits.

Channel-to-COM .............................. ±30 V max on one channel at

a time

Isolation

Channel-to-channel .................... None
Channel-to-earth ground

Continuous ........................... 60 VDC,

Measurement Category I,
(Double insulation)

Withstand ............................. 1,000 V

rms

, verified by a 5 s

dielectric withstand test

Measurement Category I is for measurements performed on
circuits not directly connected to the electrical distribution system
referred to as

MAINS

voltage. MAINS is a hazardous live electrical

supply system that powers equipment. This category is for
measurements of voltages from specially protected secondary
circuits. Such voltage measurements include signal levels, special

«
...
17
18
19
20
21
...
»

Summary of Contents for 781069-01


























Reviews:

No comments