National Instruments 781069-01 Operating Instructions And Specifications Download Page 10 | Manualshive

Page: 10 / 25

National Instruments 781069-01 Operating Instructions And Specifications Download Page 10

NI 9207E Operating Instructions and Specifications

10

ni.com

Connecting Current Channels

You can connect an external power supply to the NI 9207E. This
power supply provides the current for the devices you connect to
the module. Connect the positive lead of the power supply to a
V

sup

pin and the negative lead of the power supply to COM. Install

a 2 A maximum, fast-acting fuse between the external power
supply and the V

sup

pin. Refer to the

Specifications

more information about the V

sup

pins.

Note

The V

sup

pins are internally connected to each

other. You can connect only one external voltage supply
to the device.

Caution

Do

not

remove or insert modules if the external

power supply connected to the V

sup

and COM pins is

powered on.

You can connect single-ended current signals to the NI 9207E,
including loop-powered and three-wire current transducers.
Connect the output of the current signal to the AI pin of the channel
and the voltage supply of the current signal to V

sup

. For a

three-wire transducer, also connect the common of the device to
COM. Refer to Figures 7 and 8 for illustrations of how to connect
loop-powered and three-wire current transducers to the NI 9207E.

«
...
8
9
10
11
12
...
»

Summary of Contents for 781069-01


























Reviews:

No comments