background image

8

3.2 

Tool Change

In order to change the tools, the operator must first ensure that the grinder is switched off and the 

propane tank valve is closed. The operator should then place all the pocket weights provided in the 

weight holders on either side of the variable speed drive.
Then push machine down by the handle in a controlled manner until the grinder is resting on the 

top casters. The operator then taps the tools from the outside edging to remove, and installs new 

tools by sliding the tooling outward.

Machine must only be tilted back on firm, level surface. There is danger of machine 

falling if all weights are not used and surface is not level.

3.3 

Care & Maintenance 

Regular maintenance of the machine and its parts are imperative for functioning and safety. 
In order to prevent unnecessary downtimes, it is recommended to keep original spare and wear 

parts on stock. 

The following maintenance should take place before and after every operation of 

machine:

1.  Clean all surfaces with a dry, lint-free cloth
2.  Check all electrical connections are secure
3.  Inspect gear box for any signs of oil leakage
4.  Verify functionality of Dead Man Key.

All persons in the proximity of the machine in operation must wear safety glasses with 

lateral protection and steel-toed work boots. The machine operator must wear close-

fitting protective clothing. 

4.0 Maintenance

4.1 Recommendations
4.2  Maintenance and Inspection
4.3 Maintenance
4.4  Regular Wear Parts
4.5  Service Schedule 

4.1 Recommendations

Prior to any repair work on the machine and its drives, secure machine against uninten-

tional switch-on. Put the machine in Safety Off Position as described in chapter 2.

Summary of Contents for GP18






















Reviews: