NatComm DS2 User Manual Download Page 19 | Manualshive

Page: 19 / 24

NatComm DS2 User Manual Download Page 19

Natcomm

Page 19

RESET FACTORY DEFAULTS

DS2 can be reset back to the DEFAULT SETTINGS by entering

13579

while in

the Programming Mode.

PROGRAMMING NOTES

The following notes provide important information about the
programming procedure:

1)

To enter PROGRAMMING MODE you must turn OFF POWER to your unit and
then switch POWER ON AGAIN.

2)

Using ANY TELEPHONE connected to

DS2,

PRESS # within 30 seconds.

3)

DS2 must be not connected to a telephone line in order for your Telephone to
generate the DTMF Touch Tones that it uses for programming its functions.

4)

You will hear 3 short ‘beeps’ to confirm you are in programming mode.

5)

Individual Parameter Programming Entries are also carried out by pressing
further keys on the attached telephone.

6)

Your unit will generate 1 short ‘beep’ to confirm acceptance of command.

7)

Your unit will generate 1 long ‘beep’ to advise of an entry error.

IMPORTANT NOTE

Note - After each power up DS2 will prepare to enter programming mode
for 30 seconds. During this time, dial tone is not immediately available.

You can cancel out of this mode (before the 30 second limit) and achieve
dial tone by Hook Flashing, Hanging Up OR pressing any DTMF Touch
Tone digit other than #.

«
...
17
18
19
20
21
...
»

Summary of Contents for DS2

























Reviews:

No comments