NAPOLI ELECTRONICS NPL-3735 Owner'S Manual Download Page 6

INSTALLATION 

Notes: 

 

Choose the mounting location where 

the unit will not interfere with the 

normal driving function of the driver. 

 

Before finally installing the unit, 

connect the wiring temporarily and 

make sure it is all connected up 

properly and the unit and the system 

work properly. 

 

Use only the parts included with the 

unit to ensure proper installation. The 

use of unauthorized parts can cause 

malfunctions. 

 

Consult with your nearest dealer if 

installation requires the drilling of 

holes or other modifications of the 

vehicle. 

 

Install the unit where it does not get in 

the driver’s way and cannot injure the 

passenger if there is an emergency 

stop. 

 

If installation angel exceeds 30°from 

horizontal, the unit might not give its 

optimum performance. 

 

 

 

 

Avoid installing the unit where it would 

be subject to high temperature, such 

as from direct sunlight, or from hot air, 

from the heater, or where it would be 

subject to dust, dirt or excessive 

vibration. 

 

DIN FRONT/REAR-MOUNT 

This unit can be properly installed either 

from “Front”(conventional DIN 

Front-mount) or “Rear”(DIN Rear-mount 

installation, utilizing threaded screw holes 

at the sides of the unit chassis). For details, 

refer to the following illustrated installation 

methods. 

 

Installation Opening

 

This unit can be installed in any dashboard 

having an opening as shown below: 

 

 

 

 

 

ATTENTIONS OF INSTALLATION 

1.This player should be installed by 

professional technician. 

2. please read the instruction and 

operation of equipment carefully before 

installing.

 

3. Make sure to connect other wires 

before power connection. 

4. To avoid short circuit. Please make 

sure all the exposed wire are insulating. 

5. Please fix all the wires after 

installation. 

6. Please make connection to the 

player accordingly to this instruction 

manual. Wrong connection may cause 

damage. 

7. This player only fit for 12V DC 

device and please make sure your car 

belongs to this kind of cathode grounding 

electrical system. 

8.  Please connect the wires rightly. 

Wrong connection will cause malfunction 

or damage the electrical system. 

30

53mm

182mm

Summary of Contents for NPL-3735




















Reviews: