background image

5

6

The notch in log #5 should be pressed down onto the 

skewering pin located at the end of the grate as shown to 

prevent it from rocking. 

Position the notch located in log #6 against the grate post.

Place the bottom of log #7 against the right outermost 

grate post and the top into the pocket provided on the 

center log (#6). bend up the tab in the log support to 

cradle log #7. Tear the glowing embers into pieces and 

place onto the front of the burner. Care should be taken to 

shred the embers into thin, small irregular pieces as only 

the exposed edges of the fibre hairs will glow when 

exposed to direct flame; however care should be taken to 

not block the burner ports. blocked ports can cause an 

incorrect flame pattern, carbon deposits and delayed 

ignition.

Replacement loose material must be purchased from the original room heater manufacturer. Application of 

excess loose material may adversely affect the performance of the heater.

Log colours may vary. During the initial use of the heater, the colours will become more uniform as colour pig-

ments burn in during the heat activated curing process.

POsITIONINg ThE lOgs ImPrOPErly wIll CausE flamE ImPINgEmENT aNd CarbONINg.  

7

3.3  LOGO pLACEmENT

Remove the backing of the logo supplied and centre over the 

logo installation holes, as indicated.

LOGO

fIgurE 3.2b

fIgurE 3.2c

fIgurE 3.2d

fIgurE 3.3

11

W415-0204 / F / 10.23.08

Summary of Contents for GVFS60-N





















Reviews: