background image

W415-0788 / F / 10.21.13

44  

EN

9.2  OPERATING INSTRUCTIONS - FOR YOUR SAFETY READ BEFORE OPERATING

9.3 LIGHTING 

INSTRUCTIONS

LIGHTING INSTRUCTIONS / INSTRUCTIONS D’ALLUMAGE

1. 

  

STOP! 

READ ALL INFORMATION OF OPERATING AND LIGHTING 

      INSTRUCTIONS BEFORE PROCEEDING.

2.

   TURN OFF ELECTRIC POWER TO THE FIREPLACE.

3.

   THIS FIREPLACE IS EQUIPPED WITH AN IGNITION DEVICE WHICH 

      AUTOMATICALLY LIGHTS THE PILOT. DO NOT TRY TO LIGHT THE PILOT 
      BY HAND.

4. 

  OPEN THE GLASS DOOR.

5. 

  TURN MANUAL SHUTOFF VALVE CLOCKWISE             TO OFF.

6. 

  WAIT FIVE (5) MINUTES TO CLEAR OUT ANY GAS. IF YOU SMELL GAS 

      INCLUDING NEAR THE FLOOR, 

STOP!

 FOLLOW “B” OF THE OPERATING 

      INSTRUCTIONS. IF YOU DON’T SMELL GAS GO TO THE NEXT STEP.

7. 

  TURN MANUAL SHUTOFF VALVE COUNTER-CLOCKWISE              TO ON.

8. 

  CLOSE THE GLASS DOOR.

9. 

  TURN ON ALL ELECTRIC POWER TO THE FIREPLACE.

10.

   TURN ON MAIN BURNER.

1. 

  

ARRÊTEZ!

 LISEZ TOUTES LES INSTRUCTIONS DE FONCTIONNEMENT 

      ET D’ALLUMAGE AVANT DE CONTINUER.  

2.

   COUPEZ L’ALIMENTATION ÉLECTRIQUE À L’APPAREIL.

3.

   CET APPAREIL EST MUNI D’UN DISPOSITIF D’ALLUMAGE QUI ALLUME 

      LA VEILLEUSE AUTOMATIQUEMENT, N’ESSAYEZ PAS D’ALLUMER LA 
      VEILLEUSE MANUELLEMENT.

4. 

  OUVREZ LA PORTE VITRÉE.

5. 

  TOURNEZ LA SOUPAPE DE SECTIONNEMENT MANUELLE VERS LA 

      DROITE             A “OFF”.

6. 

  ATTENDEZ CINQ (5) MINUTES POUR QUE LE GAZ PUISSE  

      S’ÉCHAPPER. SI VOUS DÉTECTEZ UNE ODEUR DE GAZ, 

ARRÊTEZ!

 

      SUIVEZ « B » DANS LES INSTRUCTIONS DE FONCTIONNEMENT.

 

S’IL

      N’Y A PAS D’ODEUR DE GAZ, PASSEZ À L’ÉTAPE SUIVANTE.

7. 

  TOURNEZ LA SOUPAPE DE SECTIONNEMENT MANUELLE VERS LA 

      GAUCHE              A “ON”.

8. 

  FERMEZ LA PORTE VITRÉE.

9. 

  RÉTABLISSEZ L’ALIMENTATION ÉLECTRIQUE AU FOYER.

10. ALLUMEZ LE BRÛLEUR PRINCIPAL.

1. 

  TURN OFF ALL ELECTRICAL POWER TO THE FIREPLACE IF SERVICE IS 

      TO BE PERFORMED.

2.

   TURN MANUAL SHUTOFF VALVE CLOCKWISE              TO OFF. DO NOT 

      FORCE.

1. 

  COUPEZ L’ALIMENTATION ÉLECTRIQUE AU FOYER SI UN TRAVAIL 

      D’ENTRETIEN DOIT SE FAIRE. 

2.

   TOURNEZ LA SOUPAPE D’ARRÉT MANUELLE VERS LA DROITE 

      À “OFF” NE FORCEZ PAS.

TO TURN OFF GAS / INSTRUCTIONS POUR COUPER LE GAZ

OPERATING INSTRUCTIONS / INSTRUCTIONS D’OPERATION

FOR YOUR SAFETY READ BEFORE OPERATING / POUR VOTRE SÉCURITÉ LIRE AVANT DE FAIRE FONCTIONNER

 

 

 

 

 

 

 

 

 

 

WARNING:

 IF YOU DO NOT FOLLOW THESE INSTRUC-

TIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT 
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR 
LOSS OF LIFE.
INITIAL LIGHTING OF THE PILOT AND MAIN BURNERS 
MUST BE DONE WITH THE GLASS DOOR OFF.
DO NOT CONNECT VALVE OR WALL SWITCH TO ELEC-
TRICITY. SEE INSTALLATION INSTRUCTIONS.

A. THIS FIREPLACE IS EQUIPPED WITH AN IGNITION DEVICE WHICH AUTOMATI-
CALLY LIGHTS THE PILOT. DO NOT TRY TO LIGHT BY HAND.
B. BEFORE OPERATING SMELL ALL AROUND THE FIREPLACE AREA FOR GAS 
AND NEXT TO THE FLOOR BECAUSE SOME GAS IS HEAVIER THAN AIR AND WILL 
SETTLE ON THE FLOOR.

WHAT TO DO IF YOU SMELL GAS:

‡78512))$//*$6727+(),5(3/$&(
‡23(1:,1'2:6
‡'212775<72/,*+7$1<$33/,$1&(
‡'2127728&+$1<(/(&75,&6:,7&+'212786($1<3+21(,1<285

BUILDING.

‡,00(',$7(/<&$//<285*$66833/,(5)520$1(,*+%285¶63+21(
)2//2:7+(*$66833/,(5¶6,16758&7,216
‡,)<28&$11275($&+<285*$66833/,(5&$//7+(),5('(3$570(17

C. DO NOT TRY TO REPAIR ANY PART OF THIS ASSEMBLY. CALL A QUALIFIED 
SERVICE TECHNICIAN. FORCE OR ATTEMPTED REPAIR MAY RESULT IN A FIRE 
OR EXPLOSION.
D. DO NOT USE THIS FIREPLACE IF ANY PART HAS BEEN UNDER WATER. 
IMMEDIATELY CALL A QUALIFIED SERVICE TECHNICIAN TO INSPECT THE 
FIREPLACE AND REPLACE ANY PART OF THE CONTROL SYSTEM AND ANY GAS 
CONTROL WHICH HAS BEEN UNDER WATER.

ATTENTION: 

SI CES INSTRUCTIONS NE SONT PAS OBSERVÉES A LA 

/(775(81)(82881((;3/26,2132855$,76¶(168,95(

CAUSANT DES DOMMAGES A LA PROPRIETE, DES BLESSURES 
CORPORELLES OU PERTE DE VIE.

/¶$//80$*(,1,7,$/'(/$9(,7//(86((7'8%58/(8535,1&,3$/

DOIT SE FAIRE AVEC LA PORTE VITREE ENLEVEE.

1(5$&&25'(=3$6/$6283$3(28/¶,17(55837(85085$/$
/¶(/(&75,&,7(
&2168/7(=/(6,16758&7,216'¶,167$//$7,21

$&(7$33$5(,/(67081,'¶81',6326,7,)'¶$//80$*(48,$//80(/$9(,//(86(

AUTOMATIQUEMENT.

1¶(66$<(=3$6'¶$//80(5/$9(,//(86(0$18(//(0(17
%$9$17'¶$//80(56(17(=/¶$,5$87285'(/¶$33$5(,/(735Ê6'83/$1&+(5&(57$,16
*$=62173/86/285'648(/¶$,5(76('e326(5217$81,9($8'83/$1&+(53285

DÉTECTER UNE FUITE POSSIBLE.
QUE FAIRE SI VOUS DÉTECTEZ UNE ODEUR DE GAZ:

‡&283(=/¶$/,0(17$7,21'(*$=35,1&,3$/(
‡2895(=/(6)(1(75(6
‡1¶$//80(=$8&81$33$5(,/
‡1(728&+(=3$6¬$8&81,17(55837(85e/(&75,48(1¶87,/,6(=$8&817e/e3+21(

DANS VOTRE IMMEUBLE.

‡$33(/(=,00e',$7(0(179275()2851,66(85'(*$='¶817e/e3+21(92,6,1(768,9(=

SES INSTRUCTIONS.

‡6,92861(3289(=3$65(-2,1'5(9275()2851,66(85'(*$=$33(/(=/(6(59,&(

DES
INCENDIES.

&1¶(66$<(=3$6'(5e3$5(5$8&81(3,Ê&('(&(7$66(0%/$*($33(/(=81
7(&+1,&,(148$/,),e)25&(5287(17(5'(5e3$5(5/¶$66(0%/$*(32855$,7&$86(5

UN FEU OU UNE EXPLOSION.

'1¶87,/,6(=3$6&(7$33$5(,/6,81'(6(6&20326$176¬e7e68%0(5*e&217$&7(=
,00e',$7(0(17817(&+1,&,(1'(6(59,&(48$/,),e3285,163(&7(5/¶$33$5(,/(7
5(03/$&(572876<67Ê0('(&2175Ð/('(*$=728&+e3$5/¶($8

W385-0460

9.4  ANTI CONDENSATION SWITCH

This appliance has the option to go from an 
electronic intermittent pilot ignition (IPI) to a standing 
pilot (ACS) for cold climates. The anti condensation 
control switch (standing pilot) is located in the center 
of the control panel. Using your 

fi

 nger, 

fl

 ip the switch 

up for standing pilot, or down for intermittent pilot 
ignition.

ANTI CONDENSATION CONTROL 

SWITCH (ACS)

CONTROL

PANEL

Summary of Contents for GDS60-N





















































































































Reviews: