Napoleon BGNV36N Installation And Operating Instructions Manual Download Page 22

22

W415-0275 / E / 07.13.10

10.2  CARE OF GLASS

5.1

DO NOT CLEAN GLASS WHEN HOT! DO NOT USE 
ABRASIVE CLEANERS TO CLEAN GLASS. 

Buff lightly with a clean dry soft cloth. Clean both sides 
of the glass after the fi rst 10 hours of operation with a 
recommended fi replace glass cleaner. Thereafter clean 
as required. If the glass is not kept clean permanent 
discoloration and / or blemishes may result.

HOT GLASS WILL 

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

!

WARNING

10.1  DOOR GLASS REPLACEMENT

• 

Place the door frame face down careful not to scratch the 
paint.

• 

Center the gasketed glass inside the door frame with the thick 
side of the gasket facing up.

• 

Bend the glass retainers located along the edge of the door 
frame over the gasket holding the glass in place. Careful not 
to break the glass.

GLASS

GASKET

DOOR 
FRAME

GLASS 
RETAINER

!

WARNING

DO NOT USE SUBSTITUTE MATERIALS.

GLASS MAY BE HOT, DO NOT TOUCH GLASS UNTIL COOLED.

CARE MUST BE TAKEN WHEN REMOVING AND DISPOSING OF ANY BROKEN DOOR GLASS OR 

DAMAGED COMPONENTS. BE SURE TO VACUUM UP ANY BROKEN GLASS FROM INSIDE THE 

APPLIANCE BEFORE OPERATION.

DO NOT STRIKE, SLAM OR SCRATCH GLASS. DO NOT OPERATE APPLIANCE WITH GLASS 

REMOVED, CRACKED, BROKEN OR SCRATCHED. 

56.1

10.3  CARE OF PLATED PARTS

6.1

If the appliance is equipped with plated parts, you must clean fi ngerprints or other marks from the plated 
surfaces before operating the appliance for the fi rst time. Use a glass cleaner or vinegar and towel to clean. 
If not cleaned properly before operating for the fi rst time, the marks can cause permanent blemishes on 
the plating. After the plating is cured, the fi ngerprints and oils will not affect the fi nish and little maintenance 
is required, just wipe clean as needed.  Prolonged high temperature burning with the door ajar may cause 
discolouration on plated parts.

NOTE: The protective wrap on plated parts is best removed when the assembly is at room 
temperature but this can be improved if the assembly is warmed, using a hair dryer or similar heat 
source.

Summary of Contents for BGNV36N

































Reviews: