manualshive.com logo in svg

NAPCO XP-400, Installation Instructions Manual

Share
Download
NAPCO XP-400 Installation Instructions Manual Download Page 18

18

WI853C XP-400 Installation Instructions

[46]Communicator Features 2

(1) No Dial Tone Detection - Program to
disable dial tone detection for Telco 1, Telco
2 and Telco 3.

(2) 2:1 Rotary Dialing - Changes the make
break ratio when rotary dialing from 1.5:1 to
2:1.
(3) Backup if < 4 attemps - If Backup
Reporting [45-4] has been enabled, the com-
municator will use Telephone Number 2 [41]
for the remaining retries when there are less
than 4 retries remaining.

(4) Reserved

7HOHSKRQH 1XPEHU  3URJUDPPLQJ

[50] -  [59]

Programming is the same as for Telco 1.
Program to split/double report to Telco 3.
Refer to sections [30] through [39].

5HSRUW &RGHV

[60]Zone Report Codes

Report Code for Zones 1 through 4.

4/2 format - The Zone Report Code is the
1st digit of the report code sent,  the second

digit is the zone number of the reporting
zone.  For example, if zone 2 has a report-

code of 3, the report code would be 32.

3/1 format -  Sends only the report Code
and does not append it with the zone num-
ber.

[61]Point ID Report Codes

Point ID Report Codes are defaulted to
Burglary for zones 1 through 4.  Optionally,
Point ID codes for zones 1 through 4 can
be programmed as follows:

[1] Reserved

[7] Gas Alarm

[2] Panic

[8] Heat Alarm

[3] Burglary

[9] Reserved

[4] Holdup

[A] Auxiliary

[5] General Alarm

[B] 24 Hour

[6] Reserved

[62]Zone Codes

[62-1]  Restore code - Zones 1 through 8.
The second digit of the restore code is the
zone number of the restored zone.  For
example, if the Zone Restore Code [62] is
programmed to E, the restore code for that
zone would be E4 (4/2 format).
[62-2] Trouble Code  - Conditional Closing
Reports.  Zones that are bypassed at the

time of arming send this code along with the
zone number of the bypassed zone(s). For
example a conditional closing by User 2,
with zones 2 and 3 bypassed would be as
follows: 1234

C2
F2
F3

[63]System Report Codes

Program a 2-digit report code for 

Keypad

Panic 2, Keypad AUX, Keypad Panic, Test
Timer, AC Fail, Low Battery  and Trouble.

[64]System Restore Code

The code sent when a system condition
restores.  The second digit of the 2-digit
restore code is the second digit of the Sys-
tem Report Code [63].  For example, if a Low
Battery System Report Code is F8 the Bat-
tery Restore would be E8 (4/2 format).

[65]Opening and Closing Codes

Program Opening and Closing Codes for
Users 1 through 4.  The second digit of the
report code is the number of the user that
armed or disarmed the system.  For exam-
ple, if the Closing Code [65] is programmed

with a C, the closing code for User 2 would

be C2 (4/2 format).

Wi853c 
page 18

Tuesday, September 16, 1997 10:42 

Summary of Contents for XP-400





























Reviews:

No comments

Brands by name

Popular brands

Load more brands