NAPCO Magnum Alert-800 Operating Manual Download Page 13

The following information is

applicable only where local
ordinance permits use of your alarm

Control Center for fire detection

 Your

Fin 

If your alarm specialist installed

smoke detectors or heat sensing
thermostats, you have 24 hour fire

protection. This optional Fire Pro-
tection Zone is always active, even
though your system may be dis-
armed. An optional Fire Supervision
and Indicator Station on the Control

Center provides the following fire
circuit controls.

If the yellow AC light on the Fire

Supervision and Indicator Station is
off, the Control Center is not receiv-

ing AC power. Press the spring-
loaded SILENCE   FIRE RESET
switch 

 off the Mini-Sounder.

Check lights to see if there is a

general power outage. If there is,
you will be operating from your

standby battery. When AC power is

restored, the Mini-Sounder will

come back on. Press the spring-

loaded switch again to silence the

Mini-Sounder.

 

The Mini-Sounder on the Fire
Supervision and Indicator Station

signals a problem on the Fire Zone.

Press the spring-loaded SILENCE

8 FIRE 

 toshutoff the

Mini-Sounder. The red TROUBLE
light will come on until the Fire
Zone is cleared. When the zone is
restored, the Mini-Sounder will
signal again to indicate that the

Fire Zone is functional. Press the
SILENCE   FIRE RESET switch
once again to turn off the 
Sounder.

After a fire alarm, the red FIRE

ALARM light will be on. Press the
SILENCE 8 FIRE RESET switch to
clear the smoke detectors.

The fire alarm bell/siren and

standby battery should be tested
weekly. Disarm the Control Center.

Push the BATTERY   BELL TEST
switch down and listen to the bell/
siren. If the alarm sounds weak,
the battery is faulty. Call for service.

Would You 

 More

For information on home fire de-

tection, burn safety, and home fire
safety, contact the National Fire

Protection Association, Public

Affairs 

 Battetymarch

Plaza, 

 MA 02269.

NOTE: If there 

is no 

Fire Supervision and Indicator Station on your Control

Center and your Fire Zone uses smoke detectors, have your alarm specialist
show you and explain the switch he has installed for resetting the smoke

detectors after an alarm.

13

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for Magnum Alert-800

















Reviews: