![NAPCO MAGNUM ALERT 1008e Installation Instructions Manual Download Page 11](http://html1.mh-extra.com/html/napco/magnum-alert-1008e/magnum-alert-1008e_installation-instructions-manual_3339263011.webp)
MA1008e
/
1008eM
Installation Instructions
L
NAPCO Security Systems
Page 11
KEYPAD PROGRAMMING
Keypad Programming may be divided into two sub-groups:
User Program Mode and Dealer Program Mode.
USER KEY-
PAD PROGRAMMING
is limited to user codes. In the Dealer
Program Mode, the keypad provides full programming capa-
bilities.
Dealer Keypad Programming.
Set the keypad to the Dealer Program Mode: Hold down
Key [8] until a beep sounds, then enter the Dealer Program
Code. (The default Dealer Program Code is 4,5,6,7,8,9, but
this code must be reprogrammed to preserve system security.
See Glossary and the programming example, which follows).
The center segment of the numeric display will light to indicate
the Dealer Program Mode.
The Dealer Program Mode cannot be accessed while the
panel is armed or communicating
except
during the first three
minutes after power-up. (See
Power-Up Delay
in Glossary).
To shut this 3-minute "window" early, that is, before it times
out, hold down Key [9].
Note:
If the Dealer Program Mode has
been accessed during this 3-minute "window", then complete
the required programming, exit the Dealer Program Mode (see
following), power down and power up the system once again.
Set the location to be programmed by pressing Key [B] (the
three horizontal segments of the display and the green LED
will light), followed by the location number. Each location must
be entered as a three digit number, that is, 001, 020, 157, etc.
Notice that as each of the three digits is entered, the three dis-
play segments extinguish in succession from bottom to top.
When the last digit is entered, the yellow LED will light and the
display will show the data (if any) programmed in that location.
At this point, several numeric keys take on new function as-
signments, as shown in Fig. 3.
Keys [1] or [6] (Prior Location)
and
[2] or [3] (Next Loca-
tion)
- Change the location. Use Key [1] or [6] to move down
to the next lower location, or Key [2] or [3] to move up to the
next higher location. Whenever a new location is entered, a
beep will sound.
Keys [4] (Data Up)
and
[7] (Data Down)
- Select the data
for the chosen location: numbers 1-9, 0, and letters B, C, D, E,
and F, as will be indicated in the display. Key [4] sequences
data values in ascending order; Key [7], in descending order.
Key [5] (Clear)
- Clears data from the selected location
(display will go blank).
Key [8] (Exit)
- Exits the Dealer Program Mode. Hold down
until the beep sounds, then enter the Dealer Program Code
within 10 seconds to exit.
Key [B] (Set)
- Sets the location to be programmed. After
pressing Key [B], enter a three-digit location number.
To exit the Dealer Program Mode, hold down Key [8] until
the beep sounds; all four LED's will light. Within 10 seconds,
enter the Dealer Program Code; the LED's will go out. (If the
LED's go out before your code is entered, repeat this proce-
dure).
Caution:
Before exiting the Dealer Program Mode, be sure
that Location
083
contains the data shown in Table 2. lf the
control panel comes up armed on power-up, you have three
minutes to access the Dealer Program Mode. Hold down Key
[8] for two seconds, then enter your Dealer Program Code. By
checking Location
083
, you can prevent accidental erasures of
required data from going undetected. (If invalid data resides in
Location 083, a non-existent fire trouble and/or loss of keypad
functions may result). If you encounter this problem and need
assistance, call Napco's Technical Service Department (toll
free) at (800) 645-9445.
Example 1.
Reprogram the existing (default) Dealer Program Code to 8,1,5,4,8,7.
1. Hold down Key [8] until the beep sounds.
2. Enter the existing (default) Dealer Program Code, 4,5,6,7,8,9. The center segment of the display will light.
3. Set Location
244
, the first location of the Dealer Program Code block, as follows: (a) Press Key [B] (the three horizontal display
segments and green LED will light); (b) press [2],[4],[4] (the yellow LED will come on and the display will indicate the first digit of
the existing code, "4").
4. Program the first digit of the new Dealer Program Code as follows: Press Key [4] (Data Up) repeatedly until an "8" is displayed.
5. Press Key [2] (Next Location) once to advance to Location
245
, the second digit of the code. A "5" (the second digit of the de-
fault code) will be displayed. To program the second digit of the
new
code press Key [5] (Clear), then press Key [4] (Data Up)
once - a "1" will be displayed.
6. Press Key [2] (Next Location) once again to advance to the third location (
246
) of the code. Using Key [7] (Data Down), replace
the "6" with a "5".
7. Repeat this procedure, using Key [2] to advance locations and Keys [4] and [7] to select data, until the entire code has been re-
programmed. To check the code, press Key [1] (Prior Location) five times to return to Location
244
, then press Key [2] to step
through each location, noting the data displayed.
8. To exit the Dealer Program Mode, hold down Key [8] until the beep sounds, then enter the new Dealer Program Code within 10
seconds. This will confirm operation of the new code.
Disarmed
Armed
5
7, D or F
Table 2. Valid data for Location 083
4. PROGRAMMING