background image

Important:

  iBridge is a trademark of Napco Security Technologies, Inc.  All other trademarks, service marks, and product or service 

names described in this manual are for identification purposes only and may be trademarks or registered trademarks of their respective own-
ers.  

The absence of a name or logo in this document does not constitute a waiver of any and all intellectual property rights that NAPCO Se-

curity Technologies, Inc. has established in any of its product, feature, or service names or logos.  For 

NAPCO LIMITED WARRANTY

 infor-

mation, see WI1980.  

 

FCC Statement 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-
ant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against 
harmful interference in a residential installation.  This equipment generates uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications.  However, there is no guarantee that interference will not occur in 
a particular installation.  If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to cor-
rect the interference by one or more of the following measures:  

-- Reorient or relocate the receiving antenna;   
-- Increase the separation between the equipment and receiver; 
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected; 

-- Consult the dealer or an experienced radio/TV technician for help.  

Changes or modifications not expressly approved by the party responsible for compliance could void the 
user's authority to operate the equipment.   
The distance between user and products should be no less than 20cm. 

use of a momentary switch.  See the setting 

Home

 > 

Set 

Keypad as the Only View

, below.   

 

Voice

   

 

Check to enable (or uncheck to disable) IBR-TOUCH / 
IBR-TOUCH-WL touchscreen voice prompts.   

 

App Version

 

 

Displays the current version number of the IBR-TOUCH / 
IBR-TOUCH-WL firmware.   

(

continued from previous page

 

User Settings Menu

 

Summary of Contents for IBR-TOUCH













Reviews: