NAPCO Gemini GEM-X255, Installation Instructions Manual

Page: 28 / 68

X
GEM-X255 Installation Instructions
L
NAPCO Security Systems
WI1093C 3/04
!
Page 28
need of returning to the keypad to visually check after each attempt. Pressing the
C
button to restore normal operation.
Arming the system automatically cancels the Fault find Mode. Note: When testing wireless systems, the keypad will not beep
if the signal strength is less than 3, but the strength will still be displayed.
ACTIVATE LOCATE
This feature will help the user find zone troubles and indicate when they are repaired. When accessed, the sounder will
come on and the display will read "
LOCATE
", then scroll through the zones in trouble. As each zone is corrected, the sounder will
stop momentarily, signaling its repair, and the display will indicate the remaining zones in trouble. The sounder and display will
continue in this manner until all zones are repaired, or until the
C
button is pressed.
EZM ZONE FIND
To find the physical location of an EZM, enter the number of any zone on that EZM, then press the
U
button. This will
cause the EZM sounder to pulse continuously until silenced. To silence the sounder, press the
C
button on any keypad.
ACTIVATE DIALER TEST
Press YES to send a digital dialer test code to the central station using the system account number. (Be sure to notify the
central station of the impending test). A successful test will clear a Failure to Communicate system trouble.
The History Log documents the 800 most recent events.
DISPLAY ALARM LOG
Displays most recent alarm events. Line 1 displays event and date. Line 2 displays time, area and zone. To check previ-
ous alarm events, scroll back using the PRIOR button.
DISPLAY TOTAL LOG
Displays most recent events of all types. Line 1 displays event and date. Line 2 displays time and, if applicable, area and
zone or user. To check previous events, scroll back using the PRIOR button.
DISPLAY FIRE LOG
Displays most recent fire events. Line 1 displays event and date. Line 2 displays time, area and zone. To check previous
fire events, scroll back using the PRIOR button.
DISPLAY OP/CL LOG
Displays most recent openings and closings. Line 1 displays event and date. Line 2 displays time, area and user. To
check previous events, scroll back using the PRIOR button.
DISPLAY SYSTEM LOG
Displays most recent system events. Line 1 displays event and date. Line 2 displays time and other pertinent information,
where necessary, depending upon event. To check previous system events, scroll back using the PRIOR button.
TO ARM IN 1-4 HRS.
(Not for UL Installations).
Use this function to (a) delay programmed autoarming up to 4 hours, 15 minutes or (b) initiate autoarming in 4 hours, 15
minutes as follows. Note: Autoarming may not be used in UL installations.
At the "AUTOARM IN 1-4HR" display:
For 1 hour, 15 minute delay: press the
1
button, then the
U
button.
For 2 hour, 15 minute delay: press the
2
button, then the
U
button.
For 3 hour, 15 minute delay: press the
3
button, then the
U
button.
For 4 hour, 15 minute delay: press the
4
button, then the
U
button.
Fifteen minutes prior to arming, the siren will sound a 2-second warning and the keypad will begin a 15-minute countdown
with the sounder pulsing. (The sounder may be silenced by pressing the
C
button, but it will come back on one minute
before arming). Within this countdown window, arming may be delayed an additional 1 to 4 hours, as above, or autoarming
may be canceled by arming and disarming the panel.
DISPLAY AUTO ARM SCHD
(Not for UL Installations)
Press the YES button to display the autoarm schedule programmed by the PCD-Windows software. Use NEXT and
PRIOR button to scroll forward and back through the week. While the programmed schedule cannot be changed at the key-
pad, autoarming may be delayed up to four hours at the keypad, or it may be totally disabled, up to one week in advance. Se-
BA
S
IC
O
P
E
R
A
T
IO
N