manualshive.com logo in svg

NANOTEC SMCI36, Technical Manual

Share
Download
NANOTEC SMCI36 Technical Manual Download Page 19

  

Technical 

Manual

 

  

SMCI36

 

Connections and wiring

 

Setting the RS485 module address 

Hardware setting 

The RS485 module address can be set by hardware via two HEX coded switches on 
the printed circuit board. 

 

The 16's place is set with switch 1 (left) and the 1's place is set with switch 2 (right). 

Module address 

Switch 2 (right) 

Switch 1 (left) 

Software setting 

0 

0 

1 1  0 
2 2  0 
... ...  ... 
15 F 

0 

16 0 

1 

17 1 

1 

... ...  ... 
32 0 

2 

... ...  ... 
64 0 

3 

... ...  ... 
80 0 

5 

... ...  ... 
96 0 

6 

... ...  ... 
112 0 

7 

... ...  ... 
255 F 

F 

When the power supply is applied, the controller checks which address is set with the 
2 hardware switches. This hardware address is then adopted. After the address is 
changed, the power supply must be briefly switched off and on again. 

Software setting 

Both switches are set to 0 at delivery. With this setting, the address can be changed in 
the software as of firmware status 04 December 2008 or later. See the separate 
NanoPro manual. 

Issue: V 1.0 

 

19

 

Summary of Contents for SMCI36





























Reviews:

No comments

Brands by name

Popular brands

Load more brands