manualshive.com logo in svg

NANOTEC SMCI36, Technical Manual

Share
Download
NANOTEC SMCI36 Technical Manual Download Page 16

Technical Manual

 

SMCI36

 

Connections and wiring

 

3.4  Motor and power supply connection:  

Connector X3 

3.4.1 Pin 

assignment 

 

Pin 
no. 

Name Remark 

1 

GND 

Earth (0 V) 

2 A 

3 A/ 

4 B 

5 B/ 

See the data sheet of the connected stepper 
motor. 
In BLDC motors: 

•

  A = V  

•

  A/ = U 

•

  B = W 

•

  B/ = not connected 

6 

Vcc 

Operating v12 V DC ... +72 V DC 

7 

GND 

Earth (0 V) 

3.4.2  Stepper motor connection 

General information 

The motor is connected to the SMCI36 with a 4-wire cable. Twisted wire pair cables 
with braided shields are recommended. 

 

 

Danger of electrical overvoltage 

Accidentally swapping the connections will destroy the output stage. See the data 
sheet of the connected stepper motor. 
Never disconnect the motor while operating voltage is applied! 

Never

 hot-unplug lines. 

3.4.3  BLDC motor connection 

See Section BLDC motor “2.3”. 

16 

 

Issue: V 1.0

 

Summary of Contents for SMCI36





























Reviews:

No comments

Brands by name

Popular brands

Load more brands