background image

STOP

ON / STOP

START

The instrument panel allows you to start and stop the generating set, and provides you with important information 

when the generating set is under operation. Check this informations regularly while operating the generating set. 

Contact an authorized Nanni Diesel dealer if your generating set is equipped with instruments different than those 

described in this chapter.

I

 

Caution! : On a soundproof generating set

, the local/remote selector must be in 

remote

 position to start the 

generating set using the instrument panel. 

 Caution! : 

If the coolant temperature rises or the oil pressure falls abnormally, the corresponding indicators will 

illuminate and 

the generating set will stop automatically.

1. Heating. 

This  indicator  illuminates  when  the  glow

plugs are heating the combustion chambers (if fitted on

your generating set).

2. Coolant temperature. 

This indicator illuminates and

an  audible  alarm  sounds  if  the  coolant  in  the  cooling

circuit overheats.

3. Battery charge. 

This indicator illuminates when the

set is switched on. If it lights when the generating set

is running, this indicates an engine alternator charging

fault.

4. Oil pressure.

 This indicator illuminates and an au-

dible alarm sounds if the oil pressure in the lubrication

circuit falls.

5. Indicator showing presence of water in fuel filter

(if fitted).

 This indicator illuminates when there is too

much water in the fuel filter.

6. On indicator. 

This indicator shows that the generat-

ing set is powered (ignition).

7. Start/Stop  buttons. 

This  component  starts  and

stops the generating set. The ON/STOP button switch

powers  up  and  stops  the  engine.  The  START  button

starts the genset.

8. Engine  oil  pressure 

Caution!  This  indicator  does

not show the engine oil level.

 This indicator shows the

oil pressure. An audible alarm sounds and the generat-

ing set stops if the oil pressure in the lubrication circuit

falls.

9. Coolant  temperature

.  Indicates  the  coolant  tem-

perature. An audible alarm sounds and the generating

set stops if the coolant in the cooling circuit overheats.

3

6

2

4

5

1

Instrument panel

1

1

Tableau Luxe GE

Tableau Eco GE

8

9

7

3

6

2

4

5

1

7

Presentation

Summary of Contents for QMS 32T



























Reviews: