NAMCO 90500146 Operator'S Manual Download Page 36

Page: 36 / 89

Page 36

4-1

Notes on Installation

NOTE

If the location site of this machine has a polished floor it is

recommended that rubber pads are fitted under the level adjusters

to prevent the machine sliding on the floor.

In order to gain access to the Power Supply and CPU assemblies,

make sure that the rear of the machine is separated from a wall

or other machine by at least 500mm.

WARNING

NEVER turn the power to the machine ON until installation

has been completed.

WARNING

In order to prevent possible electric shocks, be sure that the

machine is connected to the mains with a securely connected

earthed plug.

WARNING

So that customers are not injured , ensure that there is at

least 500mm separation between other machines or walls.

CAUTION

In order to avoid damage to the machine due to mis-operation,
ensure that the voltage of the mains supply is 230volts AC.

Summary of Contents for 90500146


























































































Search results

Summary of Contents for 90500146

Reviews:

Related manuals for 90500146

Brands by name

Popular brands

NAMCO 90500146, Operator'S Manual

Search results

Summary of Contents for 90500146

Reviews:

Related manuals for 90500146

Brands by name

Popular brands