Nakayama WB2000, Manual

Page: 5 / 14

EN
WWW.NAKAYAMATOOLS.COM
5
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools oper-
ation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool,
taking into account the working conditions and the work to be performed.
Use of the power tool for operations different from intended could result in a hazardous situation.
Service
a. Please use a qualified expert who uses original replacement parts to repair your power tool.
This will ensure proper functioning of the power tool.
Additional safety instructions
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury.
Read all these instructions before attempting to operate this product and save these instructions.
Before using the appliance
Check the following:
• Make sure the voltage of the appliance corresponds with the power voltage;
– Are the mains lead and the mains plug in a good state: strong, without ravels or damages.
– Caution is advised when using long extension cables
• Do not use the appliance under moist circumstances;
• The metal mouthpiece gets hot. Watch out and do not touch the metal mouthpiece;
• Prevent damage of the heating element. Do not lock or block the mouth piece;
• Do not leave the appliance when switched on;
• When in operation do not point the device at people or animals
• Never look into the hot air nozzle
• Do not use this device in rain or damp surroundings, or near explosive or flammable products.
• Do not use the device on or near very dry spots to avoid fire
• Always remove the plug from the socket when not using the device, when replacing the nozzles or during maintenance of the device
• Do not point the device at the same place for longer periods of time
• Do not hold the device too close to the surface about to be worked on as the device can overheat
• Pay attention to the direct / indirect workspace as the heat can ignite flammable materials, which are close by but not necessarily in view
• Do not allow the hot parts of the device to touch the cord or other flammable materials
• The device should always be clean, dry and free of grease and oil
• Do not use the appliance for purposes other than for which it is intended.
This appliance operates at a temperature of 600 degrees without visible signs of this temperature (no flames), still there is a chance of fire risk. Watch out for
the hot air stream from the mouth piece. This air stream can cause burns.
When operating the appliance
• If you are going to use the tool, vapours and gas can be released during a short time. This can be harmful for your health. Asthmatics can suffer hindrance
of it;
• Before connecting the plug to the mains voltage you have to check if the switch is in position “0”;
• Keep the mains lead always away from the nozzle of the tool;
• Keep children and animals away from the appliance if you are using it.
• Keep all parts of the body away from the metal heating head. Do not touch it before it is cooled down.
• Carry the appliance by the handle when the metal heating head is cooled down.
• Hold the appliance by insulated gripping surfaces only, because the metal heating head may contact hidden wiring or its own cord.
Immediately switch off the appliance when:
• Plug and/or cable are defective or damaged;
• The switch is defective;
• You smell or see smoke caused by scorched insulation from the appliance.
Electrical safety
When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury.
Read the following safety instructions and also the enclosed safety instructions.
Always check that the power supply corresponds to the voltage on the rating plate.
Class II machine – Double insulation – You don’t need any earthed plug
Replacing cables or plugs
If the power cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person, in order to avoid a hazard.
Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The minimum conductor size is 1.5 mm2. When using a cable reel
always unwind the reel completely Inadequate extension cords can be dangerous. If an extension cord is used, it shall be suitable for outdoor use, and the