background image

 

 

Starting up the Hedge Trimmer 

-Please make sure that there are children or other people within a working 
range of 50 feet or 15 meters (5). Also pay attention to any animals the 
working vicinity. 
-Before operating, always check that the Hedge Trimmer is safe for operation: 
Check the security of the throttle lever    The throttle lever should be 
checked for smooth and easy action                Check for proper functioning of 
the throttle lever lock.   Check for clean and dry handles and test the 
function of the STOP switch      Keep handles free of oil and fuel 
Start the Hedge Trimmer only in accordance with the instruction. 
Do not use any other methods for starting the engine (6)! 
-Use the Hedge Trimmer only for applications specified 
-Start the Hedge Trimmer engine only after entire assembly is done Operation 
of the Hedge Trimmer is permitted\d only after all the appropriate 
accessories are attached! 
-Before starting, make sure that the cutter blade will not contact any objects 
such as branches stones etc. 
-The engine is to be stopped immediately if there are any engine problems. 
-When working with the Hedge Trimmer. Keep both hands On handles always 
wrap your fingers tightly around the handle, keeping the control handle 
cradled between your thumb and forefinger. Keep your hand in this position 
to have your machine under control at all limes. Make sure your control 
handles is in good condition free of moisture, pitch, oil or grease. 
Always ensure a safe, well-balances footing 
-Only use outdoors. 
-Operate the Hedge Trimmer in such a manner as to avoid inanition of the 
exhaust  gases. Never  run the engine in enclosed rooms(risk of suffocation 
and gas poisoning). Carbon monoxide is an odorless gas. Always ensure there 
is adequate ventilation. 
-Stop the engine when resting  and when leaving the Hedge Trimmer 
unattended.  Place it in a safe location to prevent danger to others. Setting  
fire to combustible materials or damage to the machine. 
-Never lay down the not Hedge Trimmer onto dry grass or onto any 
combustible materials. 
-Never operate the engine with a faulty expanse muffler. 
-Stop the engine during transport (7) 
-Secure the tool properly before transporting in vehicle to avoid fuel leakage. 
-When transporting the Hedge Trimmer ensure that the fuel tank is 
completely empty to avoid fuel leakage. 
 

Refueling 

-To reduce the risk of the fire and burn injury: handle  fuel with  care. It  is 
highly flammable. 
-Stop the engine before refueling(7), keep well away from open flame(8) and 
do not smoke. 
 

 
 
 

 

 
 
 
 
 
 

Summary of Contents for HT230A




















Reviews: