Nakanishi NLS-110 Operation Manual Download Page 8

Page: 8 / 8

File

FVA

Typical use of Accessories

FBA-2

FVA

LKE-2A

FBA-2

NGA

FVA

LKE-2A

FBA-2

NGA

LKE-2A

NGA

LKE-2A

FBA-2

VEA

NGA

Oil stone
Super stone

Troubleshooting

When the trouble is found, please check the following prior to consulting your dealer.

Trouble

Cause

Inspect / Corrective Action

Reciprocating stroke is poor

Low lubricant

Lubricate Oil properly

Guide Sleeve Slippage

Guide Sleeve Screw improperly

If the guide sleeve is slips after retightening,
send to NAKANISHI for repair.

Heat generation during rotation

Ball Bearing worm out by the reason Ground
Particles stock in the air of Ball Bearing

Send to NAKANISHI Repair

Abnormal Noise or Unusual
vibration during rotation

Ball Bearings worn due to debris particles
in the Ball Bearings

Ball Bearing worm out

Send to NAKANISHI Repair

Tool will not tighten

The tool mounting setscrew has loosened

Check if the tool mounting setscrew is
property positioned. Clean it and retighten.

Contents are subject to change without notice.

2015.11.20 0005

Summary of Contents for NLS-110









Search results

Summary of Contents for NLS-110

Reviews:

Related manuals for NLS-110

Brands by name

Popular brands

Nakanishi NLS-110, Operation Manual

Search results

Summary of Contents for NLS-110

Reviews:

Related manuals for NLS-110

Brands by name

Popular brands