manualshive.com logo in svg

Nakanishi KOLEC FX15WT, Instruction Manual

Share
Download
Nakanishi KOLEC FX15WT Instruction Manual Download Page 38

4. Handling Procedure

Do not put cargo at the tip of the fork. 

Adjust the fork width according to the pallet being used. 

Do not stack cargo in a condition that it may collapse.

Do not stack cargo higher than the backrest.

Do not put cargo directly on the fork.

Do not stack cargo under uneven load condition. 

Do not use a damaged pallet. 

If a damaged pallet is used, the pallet and cargo falls, and may collide with a person, resulting in injury.

Use caution when handling the fork width lock bracket.

Do not lower the fork rapidly. 

If the fork is rapidly lowered, the cargo falls and may collide with a person, resulting in injury. 

Do not step on the fork or pallet

Do not pry a cargo with the fork. 

Be careful to prevent collision of the mast with a ceiling. 

Stack cargo on a pallet so that it will not collapse. If the cargo collapses, the dropped cargo may collide
with a person, resulting in injury.

If cargo is stacked higher than the backrest, the cargo over the backrest height falls and may collide with
a person, resulting in injury.

The surface of fork is slippery. If cargo is directly put on the fork, the cargo will slip and fall, and it may
collide with a person, resulting in injury. Be sure to use a pallet to stack cargo.

If cargo is stacked under uneven load condition, the pallet may be inclined when it is raised, causing the
cargo to fall. If the cargo falls, it may collide with a person, resulting in injury.

When adjusting the fork width, handle the fork width lock bracket carefully so that your hand will not be
pinched with the bracket.

If you step on the fork or pallet, you may overturn if the forklift or fork unexpectedly moves, resulting in injury. 

If a cargo is pried with the fork, the forklift and cargo move unexpectedly, and may collide with a person,
resulting in injury.

As the fork is raised, the mast is also raised. When raising the fork, be careful to prevent collision of the
mast with a ceiling. If the mast collides with a ceiling, the cargo falls and may collide with a person,
resulting in injury.

35

If a pallet is not inserted to the root of the fork, the forklift becomes unstable and may overturn. Also, the
pallet may fall from the fork.

If the fork width is not adjusted according to the pallet being used, the pallet becomes unstable, causing
the cargo to fall.

CAUTION

Summary of Contents for KOLEC FX15WT





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands