VIDEO FORMAT CONVERSION
The T 775 is equipped with a Video Format Converter. This allows for a
simplified video connection between the T 775 and your TV Monitor when
using multiple video formats such as Composite (CVBS), S-Video, and
Component (YUV). This format change is accomplished by encoding the
analog video signal into a digital signal using a very high quality digital
encoder to maintain the best possible picture quality.
Once in digital format, the video input signal could also be available at the
other Monitor output jacks including HDMI MONITOR OUT. Thus, you do
not have to necessarily assign the video output of a composite video input
signal to MONITOR OUT (Composite video). The composite video input
signal can be viewed also at HDMI MONITOR OUT at a resolution setting
dependent upon your TV/Monitor’s resolution capability. With a composite
video input, the corresponding video resolution at HDMI MONITOR OUT
will be at 480i/576i or 480p/576p. Some TV/Monitors will automatically
display the video signal at 480p/576p if they are not capable of displaying
480i/576i.
If your TV/Monitor does not have HDMI input, select the highest quality
video format available on your TV/Monitor and utilize this as T 775’s
preferred Monitor OUT. In most cases, this will be Component Video, but on
some older TVs, S-Video maybe the best quality connection.
NOTES
• HDMI resolution cannot be downsampled. You must connect T 775’s
HDMI MONITOR OUT to your TV/Monitor HDMI input when using an
HDMI source.
• With a component video input, the corresponding output at HDMI
MONITOR OUT will be dependent upon the resolution setting of the
source.
• All three monitor outputs (Composite, S-Video and Component Video)
will always be active no matter what the source format is.
A/V PRESET
A particular Source can be assigned a stored Preset. The parameters set up
in the selected Preset number will be adopted into the particular Source it
is assigned (Please refer to the separate section on ‘A/V Presets’ for further
understanding of Preset settings).
Scrolling to ‘A/V Preset’ and by pressing and then
keys, a Source
could be assigned a Preset number ranging from Preset 1 to 5.
If it is desired not to assign the particular Source a Preset setting, select
‘None’.
TRIGGER OUT
The Trigger Out for a particular Source is dependent on the configurations
done in a separate menu on Trigger Setup (See ‘Trigger Setup’ below). If all
three available Trigger outputs are assigned to ‘Source Setup’ in the separate
‘Trigger Setup’ window, a particular Source can have the following Trigger Out
combinations
Trigger Out
➜
1
➜
2
➜
1 + 2
➜
3
➜
1 + 3
➜
2 + 3
➜
1+2+ 3
These combinations are dependent on the assignment of ‘Source Setup’ for
‘Trigger 1 Out, Trigger 2 Out or Trigger 3 Out’ at the Trigger Setup menu.
Another option is ‘None’ whereby the particular Source is not assigned any
Trigger Out.
For ‘Trigger Out’ to become enabled and assignable at ‘Source Setup
(Normal View)’ menu, make sure to carry out or note the following
beforehand
•
In the separate ‘Trigger Setup’ menu, assign ‘Trigger 1 Out, Trigger 2 Out
or Trigger 3 Out’ to ‘Source Setup.’
•
‘Trigger Out’ will not appear as an option at the Source Setup (Normal
View) menu if at the separate ‘Trigger Setup’ menu, ‘Trigger 1 Out,
Trigger 2 Out or Trigger 3 Out’ are all assigned to ‘Main, Zone 2, Zone 3,
Zone 4, or Zone 2+3+4’; with not even one ‘Trigger Out’ port allocated
to ‘Source Setup.’
OPERATION
USING THE T 775 – SETUP MENU
19
EN
G
LI
SH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ
