NAD C 725BEE User Manual Download

Page: 8 / 24

10 remote SenSor:

Point the SR 8 remote control at the remote

sensor and press the buttons. Do not expose the remote sensor of the
C 725BEE to a strong light source such as direct sunlight or illumination.
If you do so, you may not be able to operate the C 725BEE with the
remote control.

distance:

About 23ft (7m) from the front of the remote sensor.

angle:

About 30o in each direction of the front of the remote sensor.

11 record out/zone 2 Selector:

This knob doubles as both a record

and zone source selector. Rotate knob and select the Source you would
like to be directed out to REC OUT/ZONE 2 output port in the rear panel.
The directed Source signal at the REC OUT/ZONE 2 output port could
be used for making audio recordings or as an audio input to a separate
zone in your home.

about zone feature

The Zone feature allows one to simultaneously listen to another active
Source of the C 725BEE that is different from the currently selected Source.
For example, while the C 725BEE is at CD mode, you can set the RECORD
OUT/ZONE 2 SELECTOR knob to “TUNER” and the active tuned station’s
audio will be directed to REC OUT/ZONE 2 output port in the rear panel.

You can then feed the REC OUT/ZONE 2 jack to another amplifier or receiver
that is located maybe in another area of your home or building. With your
separate amplifier or receiver selecting the fed signal and with speakers
connected, you can then enjoy listening to the tuned station. You can
vary the level of the tuned station by adjusting the Volume control of the
separate amplifier, receiver or ZR 5’s [VOL

] buttons. Refer also to the

item USING THE ZR 5 REMOTE CONTROL at the REMOTE CONTROL section
of the IDENTIFICATION OF CONTROLS page.

12 volume:

The VOLUME control adjusts the overall loudness of the signals

being fed to the loudspeakers or headphones. Turn clockwise to increase
the volume setting; counter clockwise to lower it. The VOLUME control does
not affect recordings made using the REC OUT/ZONE 2 output but will
affect the signal going to the Pre-amp output (PRE OUT).

NOTE

If the Volume level is adjusted using the SR 8’s [VOL

] buttons, the

lower line of the VFD will show “Volume Up” when level is increased or
“Volume Down” if level is decreased.

13 phoneS:

A 1/4” stereo jack socket is supplied for headphone listening

and will work with conventional headphones of any impedance. The
headphone socket will work in parallel to the selected speakers. To
listen to headphones only, de-select Speakers A and/or B. The volume,
tone and balance controls are operative for headphone listening. Use
a suitable adapter to connect headphones with other types of sockets,
such as 3.5mm “personal stereo” jack plugs.

NOTE

Make certain that the volume control is turned to minimum (fully
counter-clockwise) before connecting or disconnecting headphones.
Listening at high levels can damage your hearing.

14 a SpeakerS b:

The SPEAKERS A and B buttons engage or disengage

the speakers connected respectively to the SPEAKERS A and SPEAKERS
B terminals on the rear panel. Press “A” to switch ON or OFF the speakers
connected to the SPEAKERS A terminals. Press “B” to switch ON or OFF
the speakers connected to the SPEAKERS B terminals.

15 mp Socket:

Using a 3.5mm stereo plug, connect into this socket the

audio output of a Media Player. The LED on the MP input button will
illuminate when an external Media Player is connected to this socket.

16 input SelectorS:

These buttons select the active input to the NAD

C 725BEE and the signal sent to the loudspeakers, headphones and the
PRE OUT socket. The buttons on the remote control handset duplicate
these buttons. The selected input will be displayed in the VFD.

mp (media plaYer):

Selects a line-level source connected to the MP

sockets as the active input. If the DATA port of the optional NAD IPD 1
Dock with iPod (NAD IPD 1) is connected to the corresponding DATA
PORT in the rear panel, your iPod player docked and with the NAD IPD
1’s AUDIO OUT also connected to the rear panel MP input, the lower
line of the VFD will show “iPod Connected”. Refer also to LISTENING TO
YOUR iPod PLAYER under the OPERATION main heading.
If an external Media Player is connected to the front MP socket (using
a 3.5mm stereo plug) while listening to a MP line-level source, the
external Media Player will be directly selected with the MP line-level
source immediately disconnected. It is recommended to mute the
volume or switch to a different input before plugging/unplugging the
external Media Player cable.

cd:

Selects the CD (or other line-level source) connected to the CD

sockets as the active input.

tuner:

Toggle to select AM, FM or DAB (230V version only) tuner band.

diSc:

Selects a line-level source connected to the DISC sockets as the

active input.

aux:

Selects a line-level source connected to the AUX sockets as the

active input.

tape:

Selects the Tape (or other line-level source) connected to the

TAPE sockets as the active input.

17 tone defeat:

Tone Controls are enabled or disabled by pressing this

button. The lower line of the VFD will show “Tone Defeat” when the tone
controls are bypassed or “Tone Active” if the tone controls are enabled.

18 tone controlS:

The NAD C 725BEE is fitted with BASS and TREBLE

tone controls to adjust the tonal balance of your system. The 12 o’clock
position is “flat” with no boost or cut, and an indent indicates this
position. Rotate the control clockwise to increase the amount of Bass or
Treble. Rotate the control counterclockwise to decrease the amount of
Bass or Treble. The Tone controls do not affect recordings made using
the REC OUT/ZONE 2 output but will affect the signal going to the Pre-
amp output (PRE OUT).

19 balance:

The BALANCE control adjusts the relative levels of the left

and right speakers. The 12 o’clock position provides equal level to the
left and right channels. A detent indicates this position. Rotating the
control clockwise moves the balance towards the right. Rotating the
control counterclockwise moves the balance to the left. The BALANCE
control does not affect recordings made using the REC OUT/ZONE
2 output but will affect the signal going to the Pre-amp output (PRE
OUT).

IDENTIFICATION OF CONTROLS

front panel

LIS