NAD C 368 User Manual Download

Page: 9 / 20

USING THE SR 9 REMOTE CONTROL

The SR 9 remote control handset handles the key functions of the C 368 as well as other NAD Stereo
Receivers, Integrated Amplifiers and Preamplifiers. It has additional controls to remotely operate NAD CD
Players, AM/FM Tuners and dedicated AM/FM/DAB Tuners. It will operate up to a distance of 23ft (7m).
Alkaline batteries are recommended for maximum operating life. Two AA batteries should be fitted in the
battery compartment at the rear of the Remote Control handset. When replacing batteries, check that they
have been put in the right way round, as indicated on the base of the battery compartment.

NOTE

The remote control handset supplied with the C 368 is of a universal NAD type, designed to operate
several NAD models. Some buttons are applicable only to specific NAD models. Contact your dealer
or NAD audio specialist for assistance.

1 POWER ON & OFF:

The SR 9 remote has a separate ON and OFF button. Press the ON button

to switch the unit from Standby to operating mode. Press the OFF button to switch the unit to
Standby mode.

2 DEVICE SELECTOR:

A Device Selector button determines only what component the SR 9 will

command; it does not perform any function on the C 368. Press desired Device Selector button
for the applicable buttons to be directed to a “page” of commands relevant to the selected device.
Upon selecting a Device, you can now press the corresponding SR 9 control buttons applicable for
the selected Device.

3 INPUT SELECTORS:

Refer to the corresponding labels printed on the remote control faceplate

and their respective assigned buttons to make use of these functions. Set the DEVICE SELECTOR to
“AMP” in order to gain access to these buttons.

IMPORTANT NOTE

• There are 9 maximum Sources with discrete IR codes and they are mapped out to SR 9 input selector

buttons 1 – 9. C 368 does not have USB input, hence, BT Source selector originally assigned to input
selector “9/BT” will move over and replace input selector “USB/8”. Input selector “8” in AMP mode will
now correspond to Bluetooth source while input selector “9” will be unassigned. Refer to example below.

• If you installed the optional MDC BluOS or MDC HDM 2 module, the unassigned input selector

“9” button will be allocated to “BluOS” or “HDMI 1” source (refer to “MDC BluOS

MDC HDM 2

installed” column below).

• If you installed both optional MDC HDM 2 and MDC BluOS modules, you have to disable two or

more Sources to accommodate the corresponding Sources from both modules. Refer to the item
about “ENABLED” under “USING THE C 368” for guidance on how to enable/disable Sources.

• Under “MDC BluOS

and

MDC HDM 2 installed” column below, OPT 2, COAX 2 and PHONO were disabled

to make way for HDMI 1, HDMI 2 and HDMI 3. It is your prerogative which Sources to disable so that de-
sired Sources from installed MDC modules can be allocated and selectable from the SR 9 remote control.

SR 9 CONTROL BUTTON

(AMP MODE)

FUNCTION (Corresponds to Source number)
C 368 Default Settings

MDC BluOS OR MDC HDM 2 installed

MDC BluOS AND MDC HDM 2 installed

OPT 1

OPT 2

COAX 1

LINE 1

COAX 2

LINE 2

PHONO

Bluetooth

LINE 1

BluOS

LINE 2

HDMI 1

Bluetooth

HDMI 2

Unassigned

BluOS (or HDMI 1)

HDMI 3

4 NUMERIC KEYS:

The numeric keys allow for direct input of tracks for CD players, and direct

channel/preset access for tuners and receivers.

5 SLEEP:

Switch off specific NAD Receiver or Tuner models after a preset number of minutes. This

button control does not apply to C 368.

6 MUTE:

Press the [MUTE] button to temporarily switch OFF the sound to the speakers and

headphones. MUTE mode is indicated by the Standby LED indicator flashing for NAD Integrated
Amplifiers or “Mute” shown in the VFD of NAD Receivers. For C 368, “Mute” is shown in the display.
Press MUTE again to restore sound. Adjusting the volume level via the SR 9 or the front panel
volume knob will automatically release the mute function.

IDENTIFICATION OF CONTROLS

SR 9 REMOTE CONTROL

SR 9

OPT 1

OPT 2

COAX 1

COAX 2

PHONO

LINE 1

LINE 2

USB

BLS