NABO KI 1235, User Manual

Page: 41 / 68

EN - 40 -
Installation instructions
! It is recommended that this installation be performed by authorized technical stuff.
! Before installation, read the instructions carefully.
! Fit the refrigerator / freezer in stable kitchen units only.
!
Cabinet dimensions are changed by material of trim flap
(1)
.
1. If material of trim flap
(1)
is plastic, look at (Table.1/B1) for cabinet dimensions.
2. If material of trim flap
(1)
is metal, look at (Table.1/B2) for cabinet dimensions.
! If necessary, reverse the door according to instructions.
1. See fig.A for the necessary attachment components.
2. Open the package. Take gasket spacer
(9)
and brake into three as shown in figureD. The
middle part is door hang rail
(10)
. The other two parts are unit door spacers
(11)
. (fig.D)
3. Insert trim flap
(1)
into slot and screw by screws
(8)
. (fig.E)
4. Pass the power cord through ventilation shaft and position it so that the appliance could
be easily plugged in once it has been installed. (fig.B - fig.C)
5. Cut trim gasket
(4)
to the height of the recess and stick it on reverse side of the door
hinges of the appliance. (fig.E)
6. Raise the appliance and slide into the kitchen unit.
7. Lean the appliance to the kitchen unit through the hinges and align the front feet with front
surface of the kitchen unit. (fig.F)
8. Open the appliance door and screw the front feet by using screws
(7)
. (fig.G)
9. Screw trim flap
(1)
to kitchen unit using screws
(7)
. (fig.G)
10. Screw the hinges to the kitchen unit using screws
(7)
. (fig.G)
11. Close the appliance door. Unscrew and remove the
nuts
(14)
,
washers
(13)
and
adjustment
bolts
(12)
from the appliance door. (fig.H)
12. Take out the liners of the tapes on door hang rails
(10)
. Place door hang rails
(10)
on the
appliance door by inserting the bosses on the holes of the appliance door, aligning the
front surfaces of the
door hang rails
(10)
and the appliance door parallel to each other. Let
the door hang rails
(10)
, stick onto the appliance door. (fig.H)
13. Slide the door hang
(2)
into door hang rails
(10)
. (fig.J – fig.K)
14. Take out the liners of the tapes on the front side of the door hang
(2)
.
15. Take out the liners of the tapes on the unit door spacers
(11)
and and stick them onto the
unit door
(15)
, closer to the upper corners. (fig.K)
16. Lean the unit door
(15)
to the door hang
(2)
, aligning the unit door spacers
(11)
on the left,
right and top edges with the sides of the unit or the doors of the nearer and upper kitchen
units. (fig.K)
17. Make sure that the unit door
(15)
sticks onto the door hang
(2)
. Pull the unit door
(15)
allowing
the door hang
(2)
to slide out the door hang rails
(10)
. Observe that the door hang
(2)
stays
stuck on the unit door
(15)
. (fig.L)
18. Lay down the
unit door
(15)
on the floor and screw the
door hang
(2)
to the
unit door
(15)
by screws
(7)
. (fig.L)
19. To overcome some of the furniture mistakes, there are plastic spacers
(A)
sticked on the
door hang
(2)
. Remove these plastic spacers
(A)
. (fig.M)