LIGHT
OPTIONAL ACCESSORIES
9000 – Chemical Injection Sprayer
& Adjustable Spray Gun
The following accessories and tools are available for this unit, and can
be purchased separately at your local Mytee dealer. You can find more
information on any of them at www.mytee.com
Electric Converter Kit™ (5000)
3” Stainless Steel
Upholstery Tool
(8400)
Mytee-Dry™
(2200)
SS-EZ Kit Includes:
8300 - 12” E.Z.
Glider
TM
S-Bend
Dual Jet Wand
with glide
8100 - 25’
Vacuum &
Solution Hose
•
•
Stainless Steel
Crevice Tool
(8700)
Tradewind™ Airmover
(3000)
System Maintainer
(3601)
TROUBLESHOOTING
SYMPTOM:
UNIT WILL NOT TURN ON:
PROBLEM:
Not plugged in.
SOLUTION:
Plug machine in proper outlet.
PROBLEM:
Circuit breaker has popped.
SOLUTION:
Reset circuit breaker. Make sure no other items are
running on the same circuit as machine. Outlet must
be a 20-amp circuit.
SYMPTOM:
PUMP IS NOT RUNNING PROPERLY:
PROBLEM:
Quick disconnects are not completely locked together.
SOLUTION:
Snap quick disconnects firmly together.
PROBLEM:
The solution tank is empty.
SOLUTION:
Fill the solution tank up with a premixed liquid detergent.
PROBLEM:
Jet on upholstery tool is clogged.
SOLUTION:
Clean jet with soft wire brush or remove jet and flush clean.
PROBLEM:
Filters are clogged.
SOLUTION:
Remove filters and rinse clean with water.
PROBLEM:
Heater is blocked with hard water deposits.
SOLUTION:
Flush out heaters with Mytee Products, Inc. system
maintainer solution.
PROBLEM:
Brass check valve is stuck.
SOLUTION:
Replace with new check valve.
PROBLEM:
Pump wire has become disconnected.
SOLUTION:
Reconnect wire.
PROBLEM:
Switch on switch plate is bad.
SOLUTION:
Replace switch.
PROBLEM:
Pump motor brushes are worn out.
SOLUTION:
Replace pump.
SYMPTOM:
HEATER IS NOT WORKING PROPERLY:
PROBLEM:
The back up sensor, mounted on the heater has popped.
SOLUTION:
Reset sensor by pushing in button.
PROBLEM:
Heating element is bad.
SOLUTION:
Replace element.
SYMPTOM:
VACUUM MOTOR IS NOT WORKING PROPERLY:
PROBLEM:
Hose not connected tightly to upholstery tool or machine.
SOLUTION:
Connect hose tightly.
PROBLEM:
Drain valve is not shut completely.
SOLUTION:
Close drain valve completely.
PROBLEM:
Vacuum tank lid is not on tightly.
SOLUTION:
Secure the vacuum tank tightly.
PROBLEM:
Ball float is shut off.
SOLUTION:
Empty the vacuum tank of all wastewater.
PROBLEM:
Water is coming out of vacuum motor.
SOLUTION:
Use a low foaming detergent.
PROBLEM:
Upholstery tool or wand is clogged with hair, carpet
fibers and or debris.
SOLUTION:
Clean upholstery tool or floor wand jets.
PROBLEM:
Ball float is not installed correctly.
SOLUTION:
Make sure that ball float is firmly installed on the elbow.
This machine is intended for commercial use. It is
designed to clean carpet and upholstery in an indoor
environment and is not constructed for any other
use. Use only recommended cleaning solutions and
accessory tools.
All operators must read, understand and practice
the following safety precautions.
The following safety alerts symbols are used
throughout this manual as indicated in their description:
WARNING: To warn of hazards or unsafe practices
which could result in severe personal injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
The following information signal potentially dangerous
conditions to the operator or equipment:
FOR SAFETY:
1. Do not operate machine:
• Unless trained and authorized.
• Unless operator manual has been read and
understood.
• In flammable or explosive areas.
• Unless cord is properly grounded.
• With damaged cord or plug.
• If not in proper operating condition.
• In outdoor areas.
• In standing water.
2. Before operating machine:
• Make sure all safety devices are in place and
operate properly.
3. When using machine:
• Do not run machine over cord.
• Do not pull machine by plug or cord.
• Do not pull cord around sharp edges or
corners
• Do not unplug by pulling on cord.
• Do not stretch cord.
• Do not handle plug with wet hands.
• Keep cord away from heated surfaces.
• Report machine damage or faulty operation
immediately to your distributor.
• Follow mixing and handling instructions on
chemical containers.
4. Before leaving or servicing machine:
• Turn off machine.
• Unplug cord from wall outlet.
5. When servicing machine:
• Unplug cord from wall outlet.
• Avoid moving parts.
• Do not wear loose jackets, shirts, or sleeves.
• Use manufacturer supplied or approved
replacement parts.
SAFETY PRECAUTIONS
Machine must be grounded.
If it should malfunction
or breakdown, grounding
provides a path of least
resistance for electrical
shock. This machine is
equipped with a cord having
an equipment-grounding
conductor and grounding
plug. The plug must be
plugged into an appropriate
outlet that is properly
installed in accordance
with all local code and
ordinances. Do not remove
ground pin; if missing,
replace plug before use.
WARNING:
Hazardous Voltage. Shock
or electrocution can result.
Always unplug machine
before servicing.
WARNING:
Flammable materials can
cause an explosion or
fire. Do not use flammable
materials in tank(s).
WARNING:
Flammable materials or
reactive metals can cause
an explosion or fire.
!
!
!
!
45º Elbow
HEATER
VACUUM
STEP 1
STEP 10
STEP 9
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7
STEP 8
STEP 17
STEP 20
STEP 19
STEP 18
STEP 11
STEP 12
STEP 13
STEP 14
STEP 15
STEP 16
WHEN WORK
IS COMPLETE,
UNPLUG CORDS
AND HOSES.
WRAP AND CLEAN
HOSES. CLEAN
ALL TANKS.
WHEN FLOAT
SHUTS OFF
VACUUM, EMPTY
TANKS.
TO CLEAN HEAVILY
SOILED AREAS,
REPEAT CLEANING
FROM DIFFERENT
DIRECTION.
WAIT 8 - 10
MINUTES FOR
UNIT TO PRE-HEAT.
RE-KEY WAND
UNTIL HOT WATER
BEGINS FLOWING.
ONCE HOT WATER IS
FLOWING, RELEASE
WAND AND PRE-HEAT
AN ADDITIONAL
4-5 MINUTES.
TURN ON THE
VACUUM MOTORS.
WORK AWAY
FROM CORDS
TO AVOID
DAMAGE.
FOR UPHOLSTERY
CLEANING, UNPLUG
WAND AND ATTACH
UPHOLSTERY
TOOL.
BEGIN CLEANING.
MAKE TWO DRY
PASSES TO EVERY
WET PASS.
USE A
DEFOAMER
IN YOUR
RECOVERY
TANK.
KEY WAND
UNTIL YOU
HAVE A
STEADY FLOW.
RELEASE
WAND
TRIGGER.
TURN ON
HEATER.
TURN ON PUMP
AND PRIME FOR 30
SECONDS USING
PRIME LEVER.
ENSURE
DUAL
CIRCUIT
FINDER IS
LIT.
PLUG UNIT
INTO (2) 20 AMP
GROUNDED
OUTLETS.
ATTACH
HOSES TO
TOOL.
ATTACH HOSES.
FILL
SOLUTION
TANK.
FAQ’s For speedster 1003dX
Q:
How much does the 1003dX weigh and
what are the shipping dimensions?
A:
140 pounds - Box dimensions are
20”x30”x47”. Must ship motor freight.
Q:
What comes standard with the 1003dX?
A:
the 1003dX comes with one hose hanger
(H375), one drain spout (H226), and two
extension cords (e530). please see owner’s
manual for breakdown.
Q:
does Mytee recommend a tool for the
machine?
A:
A variety of tools can be used with the unit,
including our 8300 wand, 8400 upholstery tool,
and sM100 rotary extractor.
Q:
Where do I plug the machine in?
A:
the 1003dX requires two separate 20A grounded
circuits. please note: GFI outlets may trip before
the breaker setting.
Q:
How will I know when I find two separate
circuits?
A:
the amber indicator light on the switch plate will
illuminate when the power cords are plugged into
two separate circuits.
Q:
What is the proper pre heat cycle for the
1003dX?
A
turn pump switch to the on position and prime
pump through the solution hose and the tool.
then turn the heater switch to the on position.
Let the machine sit idle for 8-10 minutes. spray
tool until you feel the hot water from the jet. Let
machine sit idle for 3-5 minutes. this will insure
the water in the heater and hoses will be at the
hottest point to start cleaning.
Q:
How do I prime the pump for 1003dX?
A:
Hook up hoses and tool to the machine. turn
then press the prime lever to release the air from
the pump head.
Q:
Are the pumps re-buildable for the 1003dX?
A:
Yes, both the seals and the pistons have repair
kits available. please see the pump manual that
shipped with your machine for the maintenance
schedule.
Q:
Is there anything I can do to increase the
expected life of my machine?
A:
running the vacuum motors with the tank empty
and lid off will allow excess moisture in the
vacs to dry off. You should also run a system
Maintainer through the system to keep the hoses,
pump, and heater clean and free of debris.
Mini-Tradewind™
(2700)