manualshive.com logo in svg

MYERS LV Series, Manual

Share
Download
MYERS LV Series Manual Download Page 5

4 

 

115159H -  LV I/O OPTION 

Using the arrow keys, choose the desired function, and press enter.  
Using the arrow keys, choose the appropriate Active state, and press enter.  
Using the arrow keys, choose the appropriate label, and press enter. 
Press escape to leave the 

I/O Settings

 menu and the changes will be updated. 

 
 

To set an output function: 
 

Ensure that the Series LV unit is fully powered and contains an I/O Board option. 
Hold down the power button on the display to power it on. 
Using the arrow keys, navigate to 

System Setup

 in the display menu. 

Using the arrow keys, navigate to 

I/O Settings

 in the System Setup menu. 

Using the arrow keys, choose the appropriate output, and press the enter button. 
Using the arrow keys, choose the desired function, and press enter. 
Using the arrow keys, set the required range if needed, and press enter.  
Press escape to leave the 

I/O Settings

 menu and the changes will be updated. 

 
 

To view the status of inputs and outputs: 
 

Ensure that the Series LV unit is fully powered and contains an I/O Board option. 
Hold down the power button on the display to power it on. 
Using the arrow keys, navigate to 

Contact Status

 in the display menu. 

Using the arrow keys, navigate to through the I/O in the Contact Status menu. 
The menu displays the state of the contacts as well as the function they are set too. 

 
 

Default settings: 
 

The following table outlines the default settings for different versions of the 

LV series I/O Option board. 

 

Table 2.1:  Default settings 

 

•

 

Default settings are factory programmed. 

•

 

Basic LV System I/O boards are not adjustable. 

6 Output Option 

3 Output / 3 Input Option 

I/O 

Default Setting 

I/O 

Default Setting 

OUT1 

Advanced: VAC In (Function)  

(Utility VAC N14% / -15%)

 

IN1 

Isolated Power Input 

Basic: AC Present (Status)

 

(AC Utility above 60VAC)

 

OUT2 

Input Fuse Failed (Alarm) 

IN2 

Isolated Power Input 

OUT3 

On Battery (Status) 

(Inverter On) 

IN3 

Isolated Power Input 

OUT4 

Overload (Alarm) 

(AC Output Turns Off if On Battery) 

OUT1 

Active when IN1 Power Present or 

when On Battery 

OUT5 

Battery Voltage (Function) 

(Near Low Battery = 1.85V / Cell) 

OUT2 

Active when IN2 Power Present or 

when On Battery 

OUT6 

Test Failed (Alarm)

 

OUT3 

Active when IN3 Power Present or 

when On Battery 

Summary of Contents for LV Series




















Reviews:

No comments

Brands by name

Popular brands

Load more brands