background image

     

5 N b + I2 (P + N - 5 G)

            5 (I1 + I2) - I2

M >

10

  

Subject to modifications

3.   IDENTIFICATION PLATE

The identification plate is located inside the loader’s right arm.

The serial number and loader model shown on this plate must be quoted in any request for spare parts information 

or technical assistance.

4.   COUNTERWEIGHT

The stability of the tractor-loader unit can only be ensured with a counterweight installed on the rear of the tractor. 

 

This should ensure that 20% of the gross weight (tractor, loader, implement, maximum load and counterweight) bears on 

the rear axle of the tractor for optimum working safety. 

The formula below is used to calculate the counterweight (M) (standard E A2 2010).

G: Load on the rear axle, with no counterweight, with empty implement (kg).

G1: Load on the front axle, with no counterweight, with empty implement (kg).

b: Distance from front axle to the implement’s centre of gravity (mm).

I1: Distance from the linkage arm pin to the rear axle (mm).

I2: Wheelbase (mm).

N: Usable load of the loader for implement pivot point (A) horizontal with the loader pivot point (B) (kg).

P: G + G1 (kg).

M: Counterweight (kg).

Summary of Contents for MX A104





































Reviews: