MW BETA 12K WIFI Installation Manual Download Page 12

 

 

                                                     

   

 

 

    12 / 14 

BETA series

 

Model:

 

BETA 12K WIFI

BETA-installation-manual-EN-R1 27.07.2020

6.4.

 

A

IR CONDITIONER OUTDOOR UNIT FUSE PARAMETER IS

 

 

250V 18K, 22K, 24K = 65TS, 25A 

 

 

 

 

7.

 

M

AINTENANCE

 

Periodic maintenance is essential for keeping your air conditioner efficient. 
 
Before carrying out any maintenance, disconnect the power supply by taking the plug out from the socket. 

 

7.1.

 

I

NDOOR UNIT

 

 

Antidust filters 

1.

 

Open the fron panel fallowing the direction of the arrow. 

2.

 

Keeping the front panel raised with one hand, take out the 
air filter with the other hand. 

3.

 

Clean the filter with water if the filter is soiled with oil, it can 
be washed with warm water (not exceeding 45°C). Leave to 
dry in a cool and fry place. 

4.

 

Keeping the front panel raised with one hand, insert the air 
filter with the other hand. 

5.

 

Close. 

 
The electrostatic and the deodorant filter (if installed) cannot be 
washed or regenerated and must be replaced with new filters after 
every 6 months. 
 

7.2.

 

C

LEANING THE HEAT EXCHANGER

1.

 

Open the fron panel of the unit and life it till its greatest 
stroke and then unhooking it form the hinges to make the 
cleaning easier. 

2.

 

Clean the indoor unit using a cloth with the water (not 
higher than 40°C) and neutral soap. Never use aggressive 
solvents or detergents. 

3.

 

If the outdoor unit is clogged, remove the leaves and the 
waste and remove the dust with air jet or a it of water. 

7.3.

 

E

ND OF SEASON MAINTENANCE

 

Disconnect the automatic switch or the plug. 

 

Clean and replace the filters. 

 

On a sunny day let the conditioner work in ventilation for 
some hours, so that the inside of the unit can dry 
completely. 

Summary of Contents for BETA 12K WIFI















Reviews: