MVP CFH-4000 User Manual Download Page 8

CFH -4000 Series Heater Manual 

Rev. 01/2013   

Page | 8  

 

Extinguishing Media – Foam, Carbon Dioxide, Dry Chemical, Water Fog. 

Copies of the above bulletins are available, at a nominal charge from: 

National Fire Protection Association 
470 Atlantic Avenue 
Boston, MA 02210 

Research  Report  No.11 of  the  American  Insurance  Association  deal  with  “Fire,  Explosion  and 
Health Hazards of Organic Peroxides”. It is published by: 

American Insurance Association 
85 John Street 
New York, NY 10038 

Local codes and authorities also have standards to be followed in the operation of your spraying 
equipment.    Your  insurance  carrier  will  be  helpful  in  answering  questions  that  arise  in  your 
development of safe procedures.

 

1.2 Personal Safety Equipment 

Magnum Venus Plastech recommends the following Personal Safety Equipment for conducting 
safe operations of the Polyester Systems: 

Magnum  Venus  Plastech  recommends  that  the  user  consult  the  state  and  local  regulations 
established for all Safety equipment listed. 

2.0 Material Safety 

2.1 Hazards Associated with Laminating Operations 

The  major  hazards  which  should  be  guarded  against  in  polyester  laminating  operations  are 
those associated with:  

1. The flammability and explosion dangers of the catalyst normally used – Methyl Ethyl Ketone 
Peroxide (MEKP). 

2.  The  flammability  dangers  of  clean-up  solvents  sometimes  used  (Magnum  Venus  Plastech 
recommends  that  clean-up  solvents  be  non-flammable),  and  of  resin  diluents  used,  such  as 
styrene. 

3. The flammability dangers of catalyst diluents, if used. (Magnum Venus Plastech recommends 
that catalyst not be diluted. 

4. The flammability dangers of the uncured liquid resins used. 

5. The combustibility dangers of the cured laminate, accumulations of over spray, and laminate 
sandings. 

6.  The  toxicity  dangers  of  all  the  chemicals  used  in  laminating  operations  with  respect  to 
ingestion, inhalation and skin and eye hazards. 

 

 

 

 

Summary of Contents for CFH-4000














































Reviews: