background image

   3 

 

EN

 

 

 

FCC statement 

 

This  device  complies  with  Part  15  of  the 
FCC  Rules.  Operation  is  subject  to  the  fol-
lowing  two  conditions:  (1)  this  device  may 
not  cause  harmful  interference,  and  (2)  this 
device  must  accept  any  interference  re-
ceived,  including  interference  that  may 
cause undesired operation. 

 
 
NOTE: 

The  grantee  is  not  responsible  for  any 

changes  or  modifications  not  expressly 
approved  by  the  party  responsible  for  com-
pliance.  Such  modifications  could  void  the 
user’s authority to operate the equipment. 

 
 

This  equipment  has  been  tested  and 

found to comply with the limits for a Class B 
digital  device,  pursuant  to  part  15  of  the 
FCC  Rules.  These  limits  are  designed  to 
provide reasonable protection against harm-
ful interference in a residential installation. 

 

This equipment generates, uses and can 

radiate  radio  frequency  energy  and,  if  not 
installed  and  used  in  accordance  with  the 
instructions,  may  cause  harmful  interfer-
ence  to  radio  communications.  However, 
there  is  no  guarantee  that  interference  will 
not occur in a particular installation. 

 

If this equipment does cause harmful in-

terference  to  radio  or  television  reception, 
which  can  be  determined  by  turning  the 
equipment  off  and  on,  the  user  is  encour-
aged  to  try  to  correct  the  interference  by 
one or more of the following measures: 

 
—Reorient or relocate the receiving antenna. 
—Increase  the  separation  between  the  equip-

ment and receiver. 

—Connect  the  equipment  into  an  outlet  on  a 

circuit  different  from  that  to  which  the  re-
ceiver is connected. 

—Consult  the  dealer  or  an  experienced  ra-

dio/TV technician for help. 

 

 

 

Summary of Contents for NeptuLink























Reviews: