MuxLab 500412 Installation & Operation Manual Download Page 6

Page: 6 / 40

HDMI 4x4 Matrix Switch Kit, HDBT, PoC, 4K/60

Installation & Operation Manual



Supports bi-directional IR control.



Built-in Graphical User Interface (GUI) for TCP/IP control.



Powerful EDID management.



Supports firmware upgrade through Micro USB port.



Easy installation, and is rack-mountable.

1.4. Package Content



One (1) HDMI 4x4 Matrix Switch



Three (3) HDBT Receivers



Four (4) IR Emitters



Three (3) IR Sensors



One (1) IR Sensor for the Matrix IR eye port



One (1) IR Remote



Two (2) Mounting Brackets and six (6) screws for the Matrix Switch



Six (6) Mounting Brackets and six (6) screws for the HDBT Receivers



One (1) RS232 Cable (3-pin Phoenix/Terminal Block to DB9)



One (1) 24VDC, 2.71A Power Adapter



One (1) Power Cord



Four (4) Trapezoidal Plastic Feet for the Matrix Switch



Twelve (12) Round plastic pads for the HDBT Receivers



One (1) User Manual

Please verify that the product and the accessories are all included; if not, please
contact your dealer.

Summary of Contents for 500412









































Search results

Summary of Contents for 500412

Reviews:

Related manuals for 500412

Brands by name

Popular brands

MuxLab 500412, Installation & Operation Manual

Search results

Summary of Contents for 500412

Reviews:

Related manuals for 500412

Brands by name

Popular brands