manualshive.com logo in svg

Mutual Power ALPINE 2600, User Manual

Share
Download
Mutual Power ALPINE 2600 User Manual Download Page 12

 

11

11. Maintenance 

 

　　

Adjustment of Glide Bars 

 

When glide bars will not slide smoothly, adjustment of glide bars is necessary. 
First, check whether or not the slides are parallel to each other, if not, loosen 
screws under the slides. Adjust the slides to make sure that they are parallel.   
If this doesn’t solve the problem, loosen screws underneath the tray table and 
adjust the rail. There should be a 0.01 to   
0.02 mm end clearance between the slide and rail so that glides will move 
freely. 

 

　　

Lubricating the machine 

 

Use a modest application of light machine oil on the rail to ensure free 
movement of slide and rail.    Also use a small amount of light machine oil 
on bearing wheels as required. 

WARNING

: do not lubricate the brake 

 

　　

Cleaning the machine 

 

Glide bars and clamps must be kept free of wax to prevent slippage.    Use 
alcohol or light, nonabrasive cleaning detergent to remove wax built-up and 
dirt from the glide bars and attaching areas of the string clamps.   

WARNING

: Do not use sandpaper or any other abrasive material on the 

glide bars and attaching area of the string clamps. 

 
 

Summary of Contents for ALPINE 2600













Reviews:

No comments

Brands by name

Popular brands

Load more brands