background image

 

VJ1626UH-I-00

ޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓޓ

VJ-1626UH INSTALLATION MANUAL 

NOTE

CAUTION

CAUTION

NOTE

6  Turning the power ON/OFF

     This section explains how to turn the printer 

ON/OFF, and how to start the sleep mode.

6.1  Turning the power ON

Follow the procedure below to turn the power ON.

1.  Press the [Power] key on the operation panel to 

turn ON the printer.

ޓ࡮

The Power lamp on the operation panel lights up 

in blue.

ޓ࡮

The printer starts initial operation.

ޓ࡮

When the initial operation is complete, the 

printer enters Normal. 

You need to let the ink flow inside the printer

   regularly, therefore, do not turn OFF the
   printer after regular operation; make sure
   you use the sleep mode.

If you have to turn OFF the printer, read 

   “3.2.2 Turning the power OFF” in the
    Operation Manual.

The procedures to turn OFF the printer

  are different for 4-color set usage and
  5-color set usage.

Long Feed

Roll

Rigid

Media Type

Heater Link

Origin

6.2  Set sleep mode on the printer

1. Make sure that the printer's operating condition is
    as follows:
  • Printing or other operation is not in  progress.
  • Operation panel display is in the Normal  condition.
  • There is ample amount of ink in the ink packs.
           Operation Manual 5.3.15 Ink Status menu
           Operation Manual 6.4.1 Replacing ink bags

  

   

 • There is enough free space in the waste fluid bottle.
           Operation Manual 6.6 Disposal the waste fluids
 • Front cover is closed.
 • Media loading lever is lowered 
   (Media loading lever on the rear side is raised).

2.  Press the [Menu] key on Operation panel.

ޓ࡮

"Menu1: Sleep Mode" is displayed on Operation 

panel.

3. Press the [>] key on Operation panel.

ޓ࡮

"Sleep Mode1: Timer Set" is displayed on 

Operation panel.

4. Press the [Enter] key on Operation panel.

ޓ࡮

"Timer: Off" is displayed on Operation panel.

Long Feed

Roll

Rigid

Media Type

Heater Link

Origin

Long Feed

Roll

Rigid

Media Type

Heater Link

Origin

Long Feed

Roll

Rigid

Media Type

Heater Link

Origin

• If there is a problem during the initial 
  operation, a message is displayed on the
  operation panel and the printer may stop 
  operating.If operation stops, refer to
  "7 Troubleshooting"and deal with the problem.

ޓ

Do not pull out or insert the power plug with
a wet hand.
This could lead to an electric shock.
Make sure to use only the specified power
supply (AC 100 V to 120 V or AC 220 V to
240 V).If a power supply other than the
specified voltage is used, it could cause an
electric shock and fire.
Take power for the printer directly from
the power socket (AC 100 V - 120 V or AC
220 V - 240 V).Do not use multiple plugs
on the same socket.This could generate
heat and might cause fire.
Be sure to use a dedicated power socket
with earth wire for the power supply, and
connect it to the earth wire.
If the earth wire is not connected, an 
electric shock or fire may occur.
Do not connect an earth wire to the following
places.
• Gas pipe
There is a possibility of ignition and explosion.
• Earth wire of telephone cables and 
lightning rods
Heavy current might flow whenever lightning
strikes.
Water pipe and faucet
The earth might not work if a plastic pipe
 is connected in the middle of the metal pipe.

Contact the retail outlet of purchase if the

ޓ

earth connection cannot be established, 

    or if the earth connection is not given.

When the power supply of the printer is 

    ON, do not pull out the power cable from
    the power socket.Whenever the plug is 
    pulled out from the power socket, allow
    one minute or more before inserting the 
    plug in the power socket again.

3.  Insert the power cable plug firmly in the socket.

• Pay attention to the following points
when handling the power supply plug.
Any mishandling of the power cable could
cause a fire.
• Make sure that no foreign substances such
as dust etc. are stuck to the power plug.
• Make sure that the power plug is firmly
 inserted to the edge of the power socket.
• When you do not use the printer for a 
 long period, make sure to pull out the
 power plug from the power socket for safety.
• If you are leaving the printer unplugged
 for a long time, follow the procedure in
"6.3.1 Operation procedure for long storage"
to turn the power OFF, and then unplug the
power plug.
• Make sure to connect an earth wire to the
earth connection that meets the following
standards.
• Earth terminal of power socket
• Earth wire with copper plate which is 
buried at 650 mm or more, deep in the
ground.
• Earth wire with copper plate which is 
 buried at 650 mm or more, deep

WARNING

Summary of Contents for VJ-1626UH

















Reviews: