VJ-1608 Hybrid INSTALLATION MANUAL
3
VJ1608HYE-I-00
Front
1
2
4
3
Front
1
2
4
3
1
2
3
Front
3
2
1
1
2
1
1
Front
1
2
4
3
3
1
1
2
2
1
2
2
3
3
3
1
2
3
3
3
1
2
3
4
5
1
2
3
2
3
1
No.
Name
1
Solenoid valve unit
2
Connection bar
No.
Name
3
Solenoid Valve unit
fastening screws
No.
Name
1
Solenoid valve unit
2
Solenoid valve cable
No.
Name
3
Printer main unit
No.
Name
1
Leg part (Right)
2
Base part
No.
Name
3
Hexagon socket head cap screws
4
Screw holes in base part
No.
Name
1
Leg part (Left)
2
Base part
No.
Name
3
Hexagon socket head cap screws
4
Screw holes in base part
No.
Name
1
Stand (Right)
2
Connector bar
No.
Name
3
Hexagon socket head cap screws
4
Tapped holes for solenoid
valve unit fastening screws
No.
Name
1
Stand (Left)
2
Connector bar
No.
Name
3
Hexagon socket head cap screws
No.
Name
1
Transfer stays
2
Stand
No.
Name
3
Butterfly screws
No.
Name
1
Leg part (Right)
2
Waste fluid tank holder
No.
Name
3
Screws
No.
Name
1
Transfer stays
2
Transfer brackets
No.
Name
3
Stand
No.
Name
1
Adjusters
No.
Name
2
Stand
No.
Name
1
Waste fluid tank holder
2
Waste fluid tank
3
Waste fluid tube
No.
Name
4
Waste fluid sensor cable
5 Waste fluid sensor connector
3 Assembling
This section explains how to assemble the printer.
Four or more people are required to
assemble this printer.
3.1 Assembling the stand
Follow the procedure below to assemble the stand.
1. Follow the procedure below to assemble the right
stand.
a. Attach the right leg part to the right base part so
that four screw holes in the base part are at the front.
b. Tighten two hexagon socket head cap screws using
a hexagonal wrench.
2. Assemble the left stand in the same way as in Step 1.
3. Fasten the connector bar to the right stand using
two hexagon socket head cap screws.
Attach the connector bar with the tapped holes for
solenoid valve unit fastening screws facing the
rear as shown below.
4. Fasten the connector bar to the left stand in the
same way as in Step 3.
5. Attach the waste fluid tank holder to the right
stand using four screws.
6. Shake the stand to make sure that each part is firmly
attached.
3.2 Attaching the stand
Follow the procedure below to attach the stand to the
printer.
1. Turn the four adjusters as shown below to prevent
the stand from moving.
2. Insert the two transfer stays into the right and left
transfer brackets, lift the printer with four or more
people and place it on the stand.
3. Remove the two transfer stays and fasten the printer
to the stand using eight butterfly screws.
4. Follow the procedure below to attach the waste fluid tank.
a. Place the waste fluid tank in the waste fluid
tank holder.
b. Attach the waste fluid tube to the tank.
c. Insert the waste fluid sensor cable into the
connector on the bottom of the printer.
3.3 Attaching the solenoid valve unit
Follow the procedure below to attach the solenoid
valve unit on the printer.
1. Ataching the solenoid valve unit to the connection
bar with the four solenoid valve unit fastening screws.
2. Attach the solenoid valve cable to the printer main
unit and the solenoid valve unit.
(Continue to next)
CAUTION