MUTOH ValueJet VJ-1624WX Operation Manual Download | Manualshive

Page: 294 / 358

background image

6 Maintenance

VJ-1624X/1624WX/1924WX OPERATION MANUAL

294

6.2 Cleaning the printer

6.2

Cleaning the printer

Periodic (every month) cleaning is necessary to use the printer in good condition.

WARNING

• Do not insert or drop metal or flammable objects into the printer through openings

such as a vent.
It could lead to an electric shock or fire.

• If foreign substances or liquids such as water entered the printer, do not use the

printer as it is.
It could lead to an electric shock or fire.
Immediately turn OFF the power switch, disconnect the power plug from the electric
socket, and contact your local MUTOH dealer.

CAUTION

• When cleaning the outer case and inside of the printer, be sure to turn OFF the

power and disconnect Power plug.

• Do not use volatile solvents such as thinner, benzene, or alcohol.

These solvents may cause damage to the paint.

• Make sure that no moisture enters the printer.

The electric circuit inside the printer may be short-circuited.

• Never open covers attached using screws under any circumstances.

This may cause an electric shock or a malfunction.

This section describes how to clean each part of the printer.

«
...
292
293
294
295
296
...
»

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1624WX

Brand: Felix printers Pages: 9

Brand: Felix printers Pages: 15

Brand: Felix printers Pages: 15

Brand: Magicard Pages: 26

Brand: QMS Pages: 194

Brand: Z Corporation Pages: 4

Brand: Datecs Pages: 29

DocuPrint 4050 NPS

Brand: Xerox Pages: 248

Brand: Oki Pages: 2

Brand: XYZ Printing Pages: 33

PIXMA E300 series

Brand: Canon Pages: 28

Brand: Canon Pages: 216

Brand: Epson Pages: 16

Brand: Epson Pages: 2

Brand: Epson Pages: 36

Brand: Epson Pages: 47

Brand: Epson Pages: 16

C11CA56203 - PictureMate Charm PM 225 Color Inkjet Printer

Brand: Epson Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands