MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 215 / 358

VJ-1624X/1624WX/1924WX OPERATION MANUAL

5 Panel setup menu

5.1 Setup menu

215

5.1.1.1.1

Print Mode menu

Settings for print quality (print mode) are set according to the usage of print data or print speed.

NOTE

After setting the Print mode, the display changes to Effect menu.

Effect menu

NOTE

• The printed images can be uneven depending on the media and print mode. In such cases, use the

following mode to clear unevenness.

• When using bidirectional print mode (refer to the following chart Details of print mode), switch it

to unidirectional print mode.

• When using Graphics 1 to 2, change it to Quality 1 to 4.

Setup item

Setting

Description

Mode

Quality 1

Sets up print mode.
• Quality 1 to 4:

Suitable for printing photos. Sets up to perform high quality printing.

• Graphics 1 to 2:

Suitable for printing photos. Sets up to perform standard printing.

• Graphics 3 to 4:

Suitable for printing illustrations, etc. Sets up to perform standard
printing.

• Banner 1 to 4:

Suitable for outdoor signs and test printing. Sets up to perform high
speed printing.

Displays details of each print mode while pressing [>] key.

Details of print mode

Quality 2

Quality 3

Quality 4

Graphics 1

Graphics 2

Graphics 3

Graphics 4

Banner 1

Banner 2

Banner 3

Banner 4

—

• [Enter] key: saves the setting and shifts to the sub menu.

Effect menu

• [Cancel] key: cancels the setting and shifts to the previous menu.

5.1.1.1 User Type advanced setup menu

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands