MUTOH ValueJet VJ-1624WX Operation Manual Download | Manualshive

Page: 217 / 358

background image

VJ-1624X/1624WX/1924WX OPERATION MANUAL

5 Panel setup menu

5.1 Setup menu

217

Effect menu

Sets up the Effect menu.
Set up this menu when you want to improve print quality by adjusting the set print mode.

NOTE

• The print quality may not be improved depending on the printing condition.

*1 The initial values of effect differ as shown below depending on the selected print mode.

Setup item

Setting

Description

Effect

<None> *1

The Effect function is not used.

Wave

The printing joint will be the wave form.
The print quality may be improved than None.

<Fog> *1

The printing joint will shade off.
Set up this menu when obvious white lines or uneven print
density appear on printed media in "Wave".
Mode for low resolution (360 x 720dpi).

<Fine&Fuzz> *1

The printing joint will shade off as the wave form.
Perform the printing at slower speed than "Wave".

<Fine&Fog> *1

The printing joint will shade off.
Set this when there is horizontal unevenness in Fine&Fuzz.
Prints at a slower speed than Fine&Fuzz.

A-S.Fine&Wave

Performs Wave printing using the half of the print head
nozzles.
Since only half of the print head nozzles are used, printing
speed becomes a half of Wave.
Set up this menu to improve the print quality compared with
"Fine&Fuzz". If used when one side of the nozzles are
clogged, quality deterioration may be avoided.

B-S.Fine&Wave

Performs "Wave" printing using the half of the print head
nozzles on the opposite side of "A-S.Fine&Wave".
Since only half of the print head nozzles are used, printing
speed becomes a half of Wave.
Set up this menu to improve the print quality compared with
"Fine&Fuzz". If used when one side of the nozzles are
clogged, quality deterioration may be avoided.

—

• [Enter] key: saves the setting and shifts to the previous

menu.

• [Cancel] key: cancels the setting and shifts to the previous

menu.

5.1.1.1.1 Print Mode menu

Print Mode

Initial effect value

Quality 1 to 4

Fine&Fuzz

Graphics 1 to 2

Fine&Fuzz

Graphics 3 to 4

Fine&Fog

Banner 1 to 2

Fog

Banner 3 to 4

None

«
...
215
216
217
218
219
...
»

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1624WX

Brand: 3Doodler Pages: 8

Brand: Raise3D Pages: 32

DRYPRO Model 793

Brand: Konica Minolta Pages: 156

Brand: Felix printers Pages: 28

Brand: Printekmobile Pages: 2

Brand: Ascend Pages: 6

Brand: IBM Pages: 16

Brand: DNP Pages: 10

NanoPrint LM210

Brand: Arrayit Pages: 23

Brand: Kyocera Pages: 173

imageRUNNER ADVANCE DX C7700 Series

Brand: Canon Pages: 127

Brand: Canon Pages: 146

Brand: PosDelta Pages: 31

Brand: POS-X Pages: 4

Brand: TECLABEL Pages: 42

COULTER AC T ANALYZER Series

Brand: Beckman Coulter Pages: 16

Brand: Nanoptix Pages: 31

Brand: EC Printer Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands