MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 177 / 358

VJ-1624X/1624WX/1924WX OPERATION MANUAL

4 Handling the printer

4.2 Media

177

4.2.6

Media feed compensation

This section explains the Media feed compensation.

The feeding length depends on the media type. The following or similar results may be seen in prints.

•

Printed images overlap.

•

White lines are printed over images.

The accuracy of media feeding may be improved with the following methods.

1. Adjust the media feed compensation value.

4.2.6.1 Procedure for the media feed compensation value

2. Fix the media firmly.

4.2.6.2 How to fix the media firmly

4.2.6.1

Procedure for the media feed compensation value

1. Display the Dist.Adj menu on Operation panel.

a. Press the [Menu] key on Operation panel.

•

"Menu1: Setup>" is displayed on Operation panel.

•

Operation panel shifts to the Setup menu display.

b. Press the [>] key on Operation panel.

•

"Set1: User Type" is displayed on Operation panel.

c. Press the [Enter] key on Operation panel.

•

"User: TypeXX" (XX is a number between 1 and 30) is displayed on Operation panel.

d. Press the [+] key or [-] key on Operation panel to select the user type to use.

e. Press the [Enter] key on Operation panel.

•

"**>1: Print Mode" is displayed on Operation panel.

TIP

The selected user type (Type 1 to 30) is displayed in "**".

5.1.1 User Type menu

Press the [+] key or [-] key on Operation panel to select "**>3: PF Adjust".

g. Press the [>] key on Operation panel.

•

"PF1: Initial Print" is displayed on Operation panel.

•

Proceed to Dist.Adj menu.

5.1.1.1.3 Media feed compensation

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands