MUTOH ValueJet VJ-1624WX Operation Manual Download | Manualshive

Page: 146 / 358

background image

Before using

VJ-1624X/1624WX/1924WX OPERATION MANUAL

146

3.6 Print quality adjustment

3.6.2.2

Custom rough adjustment pattern

Perform micro adjustment when the degree of misalignment is big.
This menu consists of the following menus.

3.6.2.2.1

Rough Pattern ALL

1. Display the Custom Adjust Print menu on Operation panel in the same way as Step 2 of

3.6.2.1 Custom confirmation pattern

2. Press the [+] key or [-] key on Operation panel to select “Adj.2: RoughPtn. ALL”.

3. Press the [Enter] key on Operation panel.

•

For VJ-1624X, "Warming Up Skip ->E" is displayed on Operation panel.
(This is not displayed for VJ-1624WX/1924WX since it does not perform warming up.)

Menu name

Description

Reference

Custom rough
adjustment
pattern

Rough Pattern
ALL

All confirmation patterns (A to F) will be
adjusted.

3.6.2.2 Custom rough

adjustment pattern

Rough Pattern A
to F

One of the confirmation patterns (A to F)
will be adjusted.

3.6.2.2.2 Rough Pattern A to F

«
...
144
145
146
147
148
...
»

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1624WX

Brand: Xerox Pages: 108

WorkCentre Pro 90

Brand: Xerox Pages: 36

Brand: Rokit Pages: 16

Brand: GearRev Pages: 41

Brand: Kyocera Pages: 44

imageRUNNER ADVANCE DX 717 Series

Brand: Canon Pages: 98

Oce VarioPrint 6000 Ultra+ Series

Brand: Canon Pages: 56

Brand: Canon Pages: 188

imageRUNNER ADVANCE C356iF III

Brand: Canon Pages: 96

Brand: Canon Pages: 218

Brand: DataCard Pages: 2

Brand: Matan Pages: 8

Cerberus B1Q101

Brand: Siemens Pages: 10

SIREMOBIL Compact CODONICS EP 1660

Brand: Siemens Pages: 30

Brand: Siemens Pages: 40

Brand: Multoo Pages: 6

Print Server R-60

Brand: TotalFlow Pages: 220

Brand: Lexmark Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands