MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 151 / 358

VJ-1624X/1624WX/1924WX OPERATION MANUAL

Before using

3.6 Print quality adjustment

151

3.6.2.2.2

Rough Pattern A to F

Print one adjustment pattern from A to F and register the set value.
The following describes how to adjust pattern A only.

1. Display the Custom Adjust Print menu on Operation panel in the same way as Step 2 of

3.6.2.1 Custom confirmation pattern

2. Press the [+] key or [-] key on Operation panel to select “Adj.3: RoughPattern A”.

3. Press the [Enter] key on Operation panel.

•

“Warming Up Skip ->E” is displayed on Operation panel.

CAUTION

• While “Warming Up” is displayed, do not touch Platen and Media guide.

They become very hot and you could burn yourself.

NOTE

•

4.4.7 Starting printing during warming up

•

A rough adjust print pattern is printed.
(Starts printing after warming up is complete.)

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands