background image

SAFETY RULES

3

F–041105C

Safe Operation Practices for  Edger.

WARNING: Look for this symbol to point out important safety precautions.

It means: “Attention! Become Alert! Your Safety Is Involved.”

WARNING:  To prevent acciden-

tal starting when setting–up,

transporting, adjusting or mak-

ing repairs, always disconnect spark

plug wire and put wire where it cannot

contact the spark plug .

Before Use

S

Read the owner’s manual carefully. Be

thoroughly familiar with the controls and

the proper use of the Edger. Know how to

stop the Edger and disengage the controls

quickly.

S

Do not operate the Edger without wearing

adequate outer garments. Wear footwear

that will improve footing on slippery sur-

faces.

S

Keep the area of operation clear of all per-

sons, particularly small children and pets.

S

Thoroughly inspect the area where the

Edger is to be used and remove all foreign

objects.

Fuel Safety

S

Handle fuel with care; it is highly flam-

mable.

S

Use an approved container.

S

Check fuel supply before each use, allow-

ing space for expansion as the heat of the

engine and/or sun can cause fuel to ex-

pand.

S

Fill fuel tank outdoors with extreme care.

Never fill fuel tank indoors. Replace fuel

tank cap securely and wipe up spilled fuel.

S

Never remove the fuel tank cap or add fuel

to a running or hot engine.

S

Never store fuel or Edger with fuel in the

tank inside a building where fumes may

reach an open flame.

Operating Safety

S

Never allow children or young teenagers to

operate the Edger.  Keep them away while

it is operating. Never allow adults to oper-

ate the Edger without proper instruction.

S

Do not operate this machine if you are tak-

ing drugs or other medication which can

cause drowsiness or affect your ability to

operate this machine.

S

Do not use this machine if you are mentally

or physically unable to operate this ma-

chine safely.

S

Always wear safety glasses or eye shields

during operation or while performing  an

adjustment or repair to protect your eyes

from foreign objects that may be thrown

from the Edger.

S

Do not put hands or feet near or under ro-

tating parts.

S

Exercise extreme caution when operating

on or crossing gravel drives, walks, or

roads. Stay alert for hidden hazards or

traffic.

S

Exercise caution to avoid slipping or falling.

S

Never operate the Edger without proper

guards, plates, or other safety protective

devices in place.

S

Never operate the Edger at high transport

speeds on slippery surfaces. Look behind

and use care when backing.

S

Never allow bystanders near the 

Edger.

S

Keep children and pets away while

operating.

S

Never operate the Edger without good visi-

bility or light.

S

Do not run the engine indoors. The ex-

haust fumes are dangerous, containing

CARBON MONOXIDE, an ODORLESS

and DEADLY GAS.

S

Take all possible precautions when leaving

the Edger unattended. Stop the engine.

S

Do not overload the Edger capacity by at-

tempting to till too deep at too fast a rate.

Summary of Contents for EV3850x4NA

























Reviews: