Murray 6271200X54 Instruction Book Download

Page: 11 / 190

1740874

WARNING: Never run the engine
indoors or in enclosed, poorly
ventilated areas. Engine exhaust

contains carbon monoxide, an odorless
and deadly gas. Keep hands, feet, hair and
loose clothing away from any moving parts
located on the engine or the snow thrower.
The temperature of muffler and nearby
areas may exceed 150

F (66

C). Avoid

these areas.

How To Start A Warm Engine

(Figure 1)

If an engine has been running and is still warm,
leave the

choke control (14)

in the off position

and do not push the

primer button (9)

. If the

engine fails to start, follow the instructions “How
To Start A Cold Engine”.

NOTE: Do not use the primer button (9) to
start a warm engine.

How To Start An Engine With A Frozen Electric
Starter

(Figure 1)

If the electric starter is frozen and will not turn
the engine, follow the instructions below.

1. Pull as much starter rope as possible out of

the starter.

2. Release the starter handle and let it snap

back against the starter. Repeat until the
engine starts.

Warm engines will cause condensation in cold
weather. To prevent possible freeze--up of recoil
starter and engine controls, proceed as follows
after each snow removal job.

1. Run the snow thrower a few minutes after

throwing snow to prevent freeze--up of the
auger/impeller.

2. With engine off, allow engine to cool for

several minutes.

3. Pull starter rope very slowly until resistance

is felt, then stop. Allow the starter rope to
recoil. Repeat three times.

4. With the engine not running, wipe all snow

and moisture from the carburetor cover in
area of controls and levers. Also, move the
choke control and starter handle several
times.

How To Remove Snow or Debris From
The Auger Housing

WARNING: Do not attempt to
remove snow or debris that may
become lodged in auger housing

with your hands. Use the clean--out tool or
a pry bar to remove snow or debris.

(Figure 5)

On some models, a clean--out tool is

attached to the top of the auger housing. Use
the clean--out tool to remove snow from the
auger housing.

(Figure 1)

Release the

auger drive lever

(5)

2. Move the

throttle control (13)

to the stop

position.

3. Pull out the

safety key (8)

4. Disconnect the spark plug wire.
5. Do not place your hands in the

auger

housing (4)

or the

discharge chute (3)

(Figure 5)

Use the

clean--out tool (1)

or a

pry bar to remove any snow or debris.

Snow Throwing Tips

1. For maximum snow thrower efficiency in

removing snow, adjust ground speed. Go
slower in deep, freezing or wet snow. If the
wheels slips, reduce forward speed.

2. Most efficient snow throwing is accomplished

when the snow is removed immediately after
if falls.

CAUTION: Do not overload the machine
capacity by attempting to clear snow at
too fast a rate.

3. For complete snow removal, slightly overlap

each previous path.

4. Whenever possible, discharge the snow

down wind.

5. For normal usage, set the skids so that the

scraper bar is 1/8” (3 mm) above the skids.
For extremely hard--packed snow surfaces,
adjust the skids upward so that the scraper
bar touches the ground.

6. Rocks and gravel must not be picked up and

thrown by the machine. On gravel or crushed
rock surfaces, set the skids at 1--1/4 inch
(32 mm) below the scraper bar. See “How To
Adjust The Height Of The Skids” in the
Maintenance section.

7. After each snow throwing job, allow the

engine to idle for a few minutes. The snow
and accumulated ice will melt off the engine.

8. Clean the snow thrower after each use.

9. Remove ice, snow and debris from the entire

snow thrower. Flush with water to remove all
salt or other chemicals. Wipe snow thrower
dry.

MAINTENANCE CHART

CUSTOMER RESPONSIBILITIES

SERVICE RECORDS

Fill in dates as you

complete regular

service.

Before