Murray 405000x8E Page 29 Instruction Book Download

Page: 29 / 52

MAINTENANCE

F-050700L

HOW TO REPLACE

THE MOTION DRIVE BELT

REMOVAL

1. Remove the mower housing. See the instructions on “How To

Remove The Mower Housing”.

2. Completely push the pedal forward and engage the parking

brake.

3. Remove the

idler pulley

(Figure 27).

Idler Pulley

Motion

Drive Belt

Loosen The

Belt Guides

Drive Pulley

Figure 27

4. To access the

belt guides

, remove the battery and battery tray.

See “How To Remove The Battery”.

5. Loosen the

belt guides

at the

drive pulley

(Figure 28).

Figure 28

Belt Guides

Seat Spring

6. Remove the

motion drive belt

from the

drive pulley

(Figure 27).

7. Remove the

adjuster nut

from the

shifter bracket

(Figure 29).

Pull the

motion drive belt

over the

shifter bracket

Adjuster Nut

Hair

Shift

Link

Shifter

Bracket

Motion Drive Belt

Figure 29

8. To remove the

motion drive belt

from the

stack pulley

, pull the

front end of the belt under the

stack pulley

and then back

between the stack pulley and the

steering plate

(Figure 30).

Motion

Drive

Belt

Figure 30

FRONT

Stack Pulley

Steering

Plate

Belt Guides

9. Remove the

access panel

(Figure 31).

10. Remove the two

screws

that attach the

steering shaft

assembly

(Figure 31). Raise the steering wheel and

steering

shaft assembly

. Pull the

motion drive belt

under the

steering

shaft assembly

Figure 31

Screw

Steering Shaft

Assembly

Motion Drive

Belt

Access Panel

11. Remove the

motion drive belt

. A correct replacement part or

assistance is available from an Authorized Service Center in

your area.

Summary of Contents for 405000x8E





















































Search results

Summary of Contents for 405000x8E

Reviews:

Related manuals for 405000x8E

Brands by name

Popular brands

Murray 405000x8E, Instruction Book

Search results

Summary of Contents for 405000x8E

Reviews:

Related manuals for 405000x8E

Brands by name

Popular brands