Murray 405000x8E Page 27 Instruction Book Download

Page: 27 / 52

WARNING: The lift lever

is spring loaded.

Make

sure the lift lever is locked

in the LEVEL ADJUST-

MENT position.

Level Adjustment

Position

Figure 22

MAINTENANCE

F-050700L

HOW TO REMOVE THE MOWER HOUSING

1. Move the

blade rotation control

to the DISENGAGE position.

2. Move the

lift lever

to the level adjustment position (Figure 22).

3. Remove the hair pins and the

washers from the

adjuster

arms

(Figure 23). See illustra-

tions “C” and “D”.

4. Remove the hair pins and wash-

ers from the

suspension links

See illustrations “A” and “B”.

5. Disconnect the

extension spring

from the

blade control rod

See illustration “E”.

6. Disconnect the

front hanger

from the axle support. See

illustration “F”.

7. Remove the

mower drive belt

from the

stack pulley

8. Pull the mower housing away from the right side of the unit.
9. To operate without the mower housing, move the lift lever to the

TOP position.

HOW TO INSTALL THE MOWER HOUSING

1. Push the mower housing under the right side of the unit.
2. Put the

mower drive belt

around the

stack pulley

. Make sure

the “V” side of the

mower drive belt

is against the

stack pulley

Also, make sure the

mower drive belt

is not twisted.

3. Attach the

front hanger

to the axle support with the

hanger

rod.

Fasten with the fasteners as shown. See illustration “F”.

4. Make sure the

mower drive belt

is between the

stack pulley

and the two

belt guides

See illustration “G”.

5. Attach the

suspension links

to the

lifter assembly

. Fasten

with the washers and hair pins. See illustrations “A” and “B”.

6. Attach the right and the left

adjuster arms

to the suspension

brackets. Fasten with the washers and hair pins. See illustra-

tions “C” and “D”.

7. Attach the

extension spring

to the

blade control rod

. See

illustration “E”.

8. Move the

blade rotation control

to the ENGAGE position.

Make sure the

mower drive belt

is inside all the

belt guides.

9. Make sure the mower housing is level. See the instructions on

“How To Level The Mower Housing”.

10. Check the operation of the

blade rotation control

. See the in-

structions on “How To Adjust The Blade Rotation Control”.

Lifter

Assembly

Blade Rotation

Control

Hanger Rod

Mower Drive Belt

Lift Lever

Figure 23

Front Hanger

Extension

Spring

Blade

Control Rod

Suspension

Link

Adjuster

Arm

Adjuster Arm

Belt

Guide

Belt

Guide

Stack Pulley

Mower Drive Belt

Suspension

Link

Summary of Contents for 405000x8E





















































Search results

Summary of Contents for 405000x8E

Reviews:

Related manuals for 405000x8E

Brands by name

Popular brands

Murray 405000x8E, Instruction Book

Search results

Summary of Contents for 405000x8E

Reviews:

Related manuals for 405000x8E

Brands by name

Popular brands