background image

INSTALLATION:

Choose configuration; Remove and reinstall Filler Plate, item  23  and reverse Drain Assembly if required for 
alternate mounting configuration.

1.   Mount Hanger Bracket to wall horizontally level as shown in Roughing-In and Dimensional Drawing. Note: Adjust height of 

Bracket if Bubbler outlet height is required to vary from that shown. Hanger Bracket MUST be securely anchored to wall 
with fasteners sufficient to support 3 times the weight of Drinking Fountain. If wall can not provide adequate support, order 
and install optional fixture support carrier.

2.   Remove the Bottom Cover from the Drinking Fountain and set aside in a safe place. Save the Screws in a secure location 

for re-use in later stages of installation.

3.   

Hang the Drinking Fountain on the Hanger Brackets ensuring the Bracket Tabs engage AND seat in the slots in the back of 

the Drinking Fountain. Verify Drinking Fountains are level, left to right AND front to back from bottom of unit. CAUTION

The Bubbler stream may be adversely affected if units are not square and level. Bottom of units and Louvers should be 
used as reference to verify unit is square and plumb.

4.   Anchor the Drinking Fountain to the wall at the lower mounting points in each Back Panel. Shim lower mounting points to 

level unit if necessary.

5.   Thoroughly flush the 3/8” O.D. supply line and then connect Drinking Fountain to Water Supply Angle Stop Valve (by 

others) with supplied 3/8” O.D. Copper Tube.

6.   Use supplied Flexible Hose and Clamps to connect Waste Tailpiece from the upper unit to the Waste Tailpiece of lower unit 

and then make up 1-1/4” O.D. P-Trap waste connection. Waste P-Trap by others.

7.   For outdoor installation, see outdoor installation instructions (Page 5)

 

STANDARD WASTE CONFIGURATION

ALTERNATE WASTE CONFIGURATION

ITEM  23

FILLER PLATE

ITEM  23
FILLER PLATE

 

A172VR

Page 4 of 10

Revised: 

12/22/17

7020-917-001

MURDOCK  MFG.  • 

15125  Proctor  Avenue  •  City  of  Industry,  CA  91746  USA 

Phone  800-453-7465  or  626-333-2543  •  Fax  626-855-4860  •  www.murdockmfg.com

Member of

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

CONTEMPORARY WATER COOLERS

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

 DRINKING FOUNTAIN

 

Summary of Contents for A172100S-UBL-VR











Reviews: