background image

 Others

1.  Under Operation of Equipment

1-1. Do not touch a capacitor directly with bare hands during operation in order to avoid the danger of
       a electric shock.

1-2. Do not allow the terminals of a capacitor to come in contact with any conductive objects (short-circuit).
       Do not expose a capacitor to a conductive liquid, inducing any acid or alkali solutions.

1-3. Confirm the environment in which the equipment will operation is under the specified conditions.
       Do not use the equipment under the following environment.
   
      (1) Being spattered with water or oil.
      (2) Being exposed to direct sunlight.
      (3) Being exposed to Ozone, ultraviolet rays or radiation.
      (4) Being exposed to toxic gas (e.g., hydrogen sulfide, sulfur dioxide, chlorine, ammonia gas etc.)
      (5) Any vibrations or mechanical shocks exceeding the specified limits.
      (6) Moisture condensing environments.

1-4. Use damp proof countermeasures if using under any conditions that can cause condensation.

2. Others

 2-1. In an Emergency

  (1) If the equipment should generate smoke, fire or smell, immediately turn off or unplug the equipment.
       If the equipment is not turned off or unplugged, the hazards may be worsened by supplying 
       continuous power.

  (2) In this type of situation, do not allow face and hands to come in contact with the capacitor or burns may be
       caused by the capacitors high temperature.

 2-2. Disposal of waste

   When capacitors are disposed, they must be burned or buried by the industrial waste vender with 
   the appropriate licenses.

 2-3. Circuit Design

  LLA Series capacitors in this catalog are not safety recognized products.
  

 2-4. Remarks

   Failure to follow the cautions may result, worst case,  in a short circuit and smoking when
   the product is used.
   The above notices are for standard applications and conditions. Contact us when the products are 
   used in special mounting conditions.
   Select optimum conditions for operation as they determine the reliability of the product after assembly.
   The data herein are given in typical values, not guaranteed ratings. 

Caution

!

JEMCAC-00640B

17

Summary of Contents for LLA185C70G105ME01 Series

























Reviews: