Munters WM36F Instruction Manual Download Page 19 | Manualshive

Page: 19 / 36

background image

19

© Munters Corporation, August 2019

QM1077r13

Figure 20A

Step 20A

Install cone onto fan by putting top of cone over top of fan. The hole in tab of one cone section should slide
down over the Frame Pin in the Main Frame assembly. Allow remainder of cone to slide over orifice panel
making sure cone support brackets remain on outside of cone.

See Figure 20A.

Frame Pin

Installation Instructions

Chapter 2

Hole in Tab of Cone Section

Step 20B

Place end of Cone Support Bracket with slot over bolt holding Cone/Strut Mounting Bracket to the orifice and
secure with Nut [DD].

See Figure 20B

.

Secure Cone to Fan installing Medium Bolt [BB] through the remaining

hole in the Cone Support Bracket and fasten with Nut [DD]. A long screwdriver may be needed to help align
the holes through Cone Support Bracket, Cone, Main Frame and Orifice. Repeat process for all 4 Cone
Support Brackets.

See Figure 20B.

Figure 20B

Nut [DD]

Medium Bolt [BB]

Nut [DD]

Use this hole for WM36F

«
...
17
18
19
20
21
...
»

Summary of Contents for WM36F





































Reviews:

No comments

Related manuals for WM36F

Brand: Danfoss Pages: 12

Brand: S&P Pages: 64

Brand: UFESA Pages: 40

Brand: Parrot Uncle Pages: 16

Brand: ebm-papst Pages: 10

Brand: ebm-papst Pages: 9

Brand: ebm-papst Pages: 10

Brand: EDM Pages: 9

Brand: Casablanca Pages: 21

Brand: Uberhaus Pages: 7

WOOZOO STF-DC18T

Brand: Ohyama Pages: 86

Brand: W. L. Gore Pages: 2

Brand: Madeira Pages: 45

Brand: S&P Pages: 52

Brand: ebm-papst Pages: 12

Tuf-Lite II 1000 Series

Brand: Hudson Pages: 10

Brand: ebm-papst Pages: 11

Brand: UltimateAir Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands