manualshive.com logo in svg

Munters CX24, Instruction Manual, Page: 12 / 14

Share
Download
Munters CX24 Instruction Manual Download Page 12

© Munters Corporation, May 2020

12

QM1108r0

Troubleshooting

6.

6.1 Troubleshooting

Fan Operating-
Insuffi  cient
Airfl ow

Excessive
Vibration

Excessive Noise

1. Fan control set above room
 temperature
2. Blown fuse or open circuit breaker
3. Propeller blade contacting fan housing
4. Fan control defective
5. Motor defective

1.  Variable speed control improperly     
 adjusted
2. Guard dirty

1.  Propeller blade contacting fan housing
2.  Motor bearing defective

3.  Frequency drive improperly adjusted

1.  Motor loose on mount
2. Propeller damaged
3.  Motor shaft bent

1.  Set to a lower temperature
2.  Replace fuse or reset breaker
3.  Realign motor in fan housing
4.  Repair or replace control
5.  Repair or replace motor

1.  See Operation, Step 2 for adjustment guidelines
2. Clean guard

1.  Sand fan housing to remove high spot
2.  Repair or replace motor bearings

3.  See operation, Step 2 for adjustments  guidelines

1. Tighten fasteners
2. Replace propeller
3.  Repair or replace motor

Fan Not Operating

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

Fan never turns off 

1.  Override thermostat set incorrectly
2.  Control set for continuous operation

1.  Set to the correct temperature
2.  Set speed control correctly

WARNING

!

Disconnect Power 

Before Servicing

WARNING

!

Moving Parts, Disconnect 

Power Before Servicing.

Summary of Contents for CX24















Reviews:

No comments