mundoclima MVD DC2 CL23530, Installation And Owner'S Manual

Page: 36 / 48

Set proper external static pressure (ESP) according to the actual installation
conditions. Otherwise it may cause some problems.
ESP can be set through the DIP switch SW2 on the main board or the new
wired controller. Please refer to Part “7.3 DIP switch settings on main board”
for SW2 setting or the wired controller manual for wired controller setting.
If the connecting duct is long and the ESP setting is small, the airflow will be
very small, leading to poor performance.
If the connecting duct is short and the ESP setting is large, the airflow will be
very large, leading to higher operating noise and even water may be blown
out through the air outlet.
Š
Š
34
Four ESP can be set through DIP switch SW2.
Twenty ESP can be set through the new wired controller.
Selection instructions for static pressure set through the wired
controller
1) The IDU static pressure can be set using the wired controller
€!&&!?\!#\!
2) Hold the "Function" "Mode" button for 5s to enter the
parameter settings interface (the unit must be off);
3) After accessing the parameter settings interface, the tempera-
\;!?Z‹‹Œ&‹‘‹;‹’‹\
switch parameter code. After "C9" is selected, press the "OK"
\&?!#!Œ&‹‘‹
;‹’‹\;“\&?\&€!#
table provides the corresponding static pressures of the values).
Press "OK" to save the parameters and complete the parameter
settings.
4) Press "Cancel" to return to the previous layer until exiting the
parameter settings, or exit the parameter settings when there
?!
5) On the parameter settings interface, the wired controller does
not respond to the remote control signal. The wired controller
does not respond to the APP remote control signal.
6)The "Mode", "Fan Speed", "Swing", "Function" and "On/Off"
buttons are invalid on the parameter settings interface.
(ex. WDC-120GWK)
Figure 6.4: Model 560
400Pa
380Pa
360Pa
340Pa
330Pa
320Pa
310Pa
300Pa(default)
290Pa
280Pa
270Pa
260Pa
240Pa
220Pa
200Pa
180Pa
160Pa
140Pa
120Pa
100Pa
25
75
125
175
225
275
325
375
425
4950 5450 5950 6450 6950 7450 7950
St
at
ic
pressure
(P
a)
Air flow (m 3 /h)
ESP1 ESP2 ESP3 ESP4
16.0kW 100Pa 50Pa 170Pa 200Pa
20.0-28.0kW
40-56kW 300Pa 100Pa 200Pa 400Pa
170Pa 100Pa 200Pa 250Pa
Capacity
00 01 02 03 04 05 06 07 08 09
16kW 30Pa 50Pa 60Pa 70Pa 80Pa 90Pa 100Pa 110Pa 120Pa 130Pa
20-28kW 30Pa 50Pa 60Pa 70Pa 80Pa 90Pa 100Pa 110Pa 120Pa 130Pa
10 11 12 13 14 15 16 17 18 19
16kW 140Pa 150Pa 160Pa 170Pa 180Pa 190Pa 200Pa 200Pa 200Pa 200Pa
20-28kW 140Pa 150Pa 160Pa 170Pa 180Pa 190Pa 200Pa 210Pa 230Pa 250Pa
40-56kW 120Pa 100Pa 140Pa 160Pa 180Pa 200Pa 220Pa 240Pa 260Pa 270Pa
280Pa 290Pa 300Pa 310Pa 320Pa 330Pa 340Pa 360Pa 380Pa 400Pa
Capacity
Figure 6.3: Models 400 / 450
100Pa
130Pa
160Pa
190Pa
220Pa
250Pa
280Pa
300Pa(default)
340Pa
360Pa
380Pa
400Pa
0
50
100
150
200
250
300
350
400
450
4300 4800 5300 5800 6300 6800 7300
St
at
ic
pressure
(P
a)
Air flow (m 3 /h)
Capacity
40-56kW